Q2-A hollow stainless-steel cylinder having an inside diameter of 4 cm and thickness of 1 cm is exposed to a convection environment at 30 C, h=50 W/m2 C. Heat is generated uniformly in the cylinder at the rate of 1 MW/m3. Determine the steady state temperature distribution in the cylinder. What are (1)-the location and (2)-the value of the maximum temperature in the cylinder? Assume the inside surface is insulated.

Q2-A hollow stainless-steel cylinder having an inside diameter of 4 cm and thickness of 1 cm is exposed to a convection environment at 30 C, h=50 W/m2 C. Heat is generated uniformly in the cylinder at the rate of 1 MW/m3. Determine the steady state temperature distribution in the cylinder. What are (1)-the location and (2)-the value of the maximum temperature in the cylinder? Assume the inside surface is insulated.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

10-What is the maximum temperature is aplane wall 8 cm thick in which that is generated uniformally at the rate 1000 W/m3 >>If one side is maintained at 20 C and the other side at 100 C ..Kw=1.5 W/mC.
3. A well-mixed cement-lined storage tank contains water initially at 50°C. The water loses energy to its surroundings via conduction through the tank's concrete-lined walls. The tank sits in an unheated warehouse with an air temperature of 0°C. A diagram of the storage tank is shown below. The cement lining is 1.5-cm thick and has a thermal conductivity (htc) of 2.0 W/(m K). height = 1.5 m diameter = 2.0 m a. How long will it take (in minutes) for the water to cool to 40°C? b. Why might you be over- or underestimating the time it will take to cool the contents of the reactor?
Q2: A long 25 cm diameter cylindrical shaft made of stainless steel 304 comes out of an oven at a uniform temperature of 500 •C. The shaft is then allowed to cool slowly in an environment chamber at 180 °C with an average heat transfer coefficient of h=90 W/m2. °C. Determine the temperature at the center of the shaft 40 min after the start of the cooling process. Also, determine the heat transfer per unit length of the shaft during this time period. Taking p=7900 kg/m3, * .Cp%3477 J/kg. •C, k= 14.9
A long rod with a thermal conductivity of 1 W / m · K is subjected to the boundary conditions given in the figure. Find the temperature distribution in the steady state with the energy balance method for ∆x = ∆y = 0.2m. Also calculate the heat transfer between rod and fluid per unit length.
A cylindrical uranium fuel rod of radius 5 mm in a nuclear reactor is generating heat at the rate of 4 x 107 W/m³ the rod is cooled by a liquid (convective heat transfer coefficient 1000 W/m²-K) at 25°C. At steady state, the surface temperature (in K) of the rod is
At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
b. A slab of stone of area (3600 + R) cm² and thickness 10 cm is exposed on the lower surface to steam of (100 + R )° C. A block of ice at 0° C rests on upper surface of the slab. In one hour 4.8 kg of ice is melted. Calculate the thermal conductivity of the stone. Consider the specific latent heat of ice is (3.36 + R) x10° Joules. R=76
What is the heat transfer rate of initial temperature of 26 degree Celsius and the final temperature is 85 degree Celsius.
Determine the time needed to decrease the temperature of a solid cylinder from 40 C to 35 C if the ambient temperature is equal to 31 C. The cylinder has a length equals to 0.9 m and diameter equals to 100 mm. The heat convective coefficient is equal to 9 W/m^2.K. The cylinder has a conductivity equals to 2 W/m.K, a density equals to 1200 kg/m^3 and its Cp is equal to 4.700 kJ/kgK.
Determine the heat stored in a concrete floor (10 cm thick, 3.5 m × 4.5 m),initial temperature 60°F, final temperature 80°F.