Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal resistance of the ammeter is 5 KN , the voltage across the internal resistance is 0.5 v and the resistance of the diodes in the forward direction is 1 KQ, find the multiplier resistance and sensitivity. Assume half wave rectification and a shunt resistance across the meter. The value of the shunt resistance across the ammeter is 2.5 KQ.

Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal resistance of the ammeter is 5 KN , the voltage across the internal resistance is 0.5 v and the resistance of the diodes in the forward direction is 1 KQ, find the multiplier resistance and sensitivity. Assume half wave rectification and a shunt resistance across the meter. The value of the shunt resistance across the ammeter is 2.5 KQ.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Diodes would be considered ideal. Which of the following is true? 1. The DI diode is in the plug. II. The DI diode is conducting. I. Diode D2 is conducting. IV. Diode D2 is in the plug.
Q1
(b) Measure (using the DVM and oscilloscope) the voltage drop Vc across the capacitor and explain the operation of the circuit. the voltage drop Vc across the capacitor is 4.61V please explain question b
What can you say about state of diodes 1, 2, 3 in the picture? A. reverse, forward, reverse B. reverse, forward, forwardC. forward, reverse, forward D. Reverse, reverse, forwardE. forward, forward, reverse
Determine 1) the maximum load current. 2) the mean load current .3)the rms alternating load current. 4) the DC power supplied to the load. 5) the input power to the anode circuit. 6) the rectification efficiency. 7) the percentage of regulation. 8) the ripple current. R=10°0 Vi R=10°n AC Figure (2-72) the circuit of problem (2-6). (2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of Ikn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode. (2-8) A zener diode has a de power dissipation of Iw and a zener voltage rating of 27v. What is the value of I, max for the device? (2-9) Calculate and draw the output voltage for the circuit shown in Figure (2-74). +100v Vo 2.2kd4 2.2kQ -100v Figure (2-74) the circuit of problem (2-10).
These are subparts of a question so please answer all and dont palagarize
5. A voltage source produces a "Triangle" wave and is connected to a series diode and resistor circuit as shown. D1 KH D V1 #1 V R1 R Using the nominal piecewise linear model for a diode, determine from the following possibilities the graph that best represents the voltage across the resistor? (Delete those that do not apply) (Blue curve VR, dashed curve V1). Then determine which graph best represents the voltage across the diode.
What are the different uses of diodes? Compare different types of diodes on the basis of speed, size, and power consumption?
Topic: Half Wave Rectification
In your opinion, what are junction diodes, and how did they come to be known as junction diodes?
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
For the bridge rectifier circuit shown in the Figure, assuming practical diodes, the peak value of the output voltage across the load resistor RL is 10:1 ... D3 D1 V% = 120V RL A) 16.97 V 18.37 V 15.57 V D 18.6 V llee