Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to İL-De 205A RL VL-DC =20V 220V rmsh 0.01 F 0.02F 0.0167 F

Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to İL-De 205A RL VL-DC =20V 220V rmsh 0.01 F 0.02F 0.0167 F

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. With necessary diagrams explain the working of a reverse biased P-N Junction Diode.
Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
Q1 A. Design a clamper to perform Silicon diodes 10 V 2.7 V the function indicated in Figure shown below. Design B. Clip the output waveform to -10 V -17.3 V (+0.7 V and -0.7 V).
Choices are: 45V 60V 10.09V 4.77V 30V 15V 9.55V 7.5V What id the right answer
The reverse recovery time for fast recovery diodes is a. 20 micro seconds b. 10 micro seconds c. 5 micro seconds d. 15 micro seconds
Given the half-wave rectifier circuit shown 220V 60Hz 220V:Es Es D RL The load resistor is 2292 and it dissipates 2W. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average diode current and PIV of the diode.
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
I need the answer as soon as possible
Electrical Engineering - elctronic Please solve the question quickly
Answer a,b,c,d
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izk = 1.5 mA and Vz = 14 V. R 560 0 VIN