Q1(c) A horizontal force P with a magnitude of 600 N is applied to the end lever of flipped L shape with diameter of 30 mm, 250 mm height and 450 mm length. Prove that the shearing force P does not cause any shearing stress at point C and principal stresses are as shown in Figure Q1(b).

Q: The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500…

A: The diameter of the rod, D = 40mmThe force at the free end, Fx=1300 N, Fy=500 N, Fz=800 N The rod is…

Q: Problem 4 The horizontal force of p 85 kN acts at the end of the plate. The plate has a thickness of…

A:

Q: For the beam shown: 3. Draw the free-body diagram (FBD) and determine the reactions at the supports…

A: Data given F = 40 kN M = 40 kNm L =1m σall = 100 MPa Find: (a) FBD with reaction at supports (b)…

Q: The internal shear force at a certain section of a steel beam is V=7.2kN.  The beam cross section…

A: Given:- Shear force, V=7.2 KN To find:- a Shear stress at point Hb Shear stress at point Kc Maximum…

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Take moment about C∑ Mc=0TBA0.125-11000.3=0TBA=2640N∑ Fx=0TBA-Cx=0Cx=2640N∑ Fy=0 Cy=1100N…

Q: 300 mm is applied to the bell crank. B -450 mm- (a) Determine the normal stress developed in e 10mm…

A:

Q: If a moment, M=10 ft-kips, is applied to the cross-section about its strong axis, what is the…

A: solve question part g and h, all require data such as depth of neutral axix and moment of inertia…

Q: The rod shown in the figure is loaded at points A and B. The circular cross section has a diameter…

A: P = Axial compression forceP = 400 KN V = Shear forceV = 20 KNT = Torque = 20*2T = 40 KN-mM =…

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A:

Q: Question 2) In the system given in the figure, a distributed load of w=85 kN/m acts on the rod AB of…

A:

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Given data,  Applied force P = 1100 N  Shear Stress in the pin = 42 MPa  We have to determine the…

Q: The internal shear force V at a certain section of an aluminum beam is 8.2 kN. If the beam has the…

A:

Q: 2. Determine the largest load P that can be applied to the frame without causing either the average…

A:

Q: Q.3) A simply supported wide-flange (see figure below) beam of span length L carries a vertical…

A: Given : Section : W 10 X 30 L = 8.5 ft P = 5 kips  Alpha = 26.57 degrees We are asked to determine…

Q: Problem 1 Knowing that L = 1 m, M = 10 kNm, F= 20 kN, 0 = 100 MPa, 1. Draw the free body diagram…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Applied force P = 1100 N Shear Stress in the pin = 42 MPa We have to determine the followings:…

Q: The split ring shown has an inner radius r1 = 0.6 in. and a circular cross section of diameter d =…

A:

Q: 2. Determine the largest load P that can be applied to the frame without causing either the average…

A: member CB has a square crosssection of 25mm sideat section a-aaverage normal stress(average shear…

Q: 1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A:

Q: Design the beam using IPE shape.

A: Since you have mentioned designing the beam using the IPE section, subpart 5 is solved below: Given:…

Q: Problem 2: Member AC is subjected to a vertical force P= 3000 N. This force is positioned as shown…

A:

Planar Stresses