Q1:Air enters a diffuser at 200 m/s with a pressure of 80 kPa and a temperature of -20°C. It leaves with a velocity of 15 m/s at an atmospheric pressure of 95 kPa. If the inlet diameter is 100 mm, determine : 1- the enters density is : Take R= O.287

Q1:Air enters a diffuser at 200 m/s with a pressure of 80 kPa and a temperature of -20°C. It leaves with a velocity of 15 m/s at an atmospheric pressure of 95 kPa. If the inlet diameter is 100 mm, determine : 1- the enters density is : Take R= O.287

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A semi-cylindrical concrete structure having a radius of 5 m and length of 3 m is rested on ground. Wind (air having a density p=1,2 kg/m3 ) at a free-sream speed of 3 m/s with an atmospheric pressure of 100 kPa far upstream the structure blows over the structure. The air entrance to the structure is at ground level corresponding to the forward stagnation point and the magnitude of minimum pressure is acting on the top of the structure a lift force is generated. Estimate the lift coefficient CL =? with calculated magnitude of lift force from potential flow theory Lütfen birini seçin: а. 2 b. 3 С. 1 d. 12 е. 4
The gauge pressure of water at AA is 150.5 kPakPa. Water flows through the pipe at AA with a velocity of 18 m/sm/s, and out the pipe at BB and CC with the same velocity vv. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mmmm at AA, and at BB and CC the diameter is 25 mmmm . ρwρw = 1000 kg/m3 Determine the xx component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Determine the yy component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium.
the power produced by the 100 mm diameter jet discharging at the nozzle is equivalent to 60 kW. compute the velocity of the jet. Answer: 24.8 m/s.
Orange juice at 20°C (pjuice=1020 kg/m3) is flowing through a horizontal U-type reducing bend. The absolute pressure is 158.5 kPa at the inlet and 150.9 kPa at the outlet. Calculate the horizontal components (x and y, but not z) and sign of the force (KN) applied to the reducing bend to hold it in place. 36 kg/s Overhead View d = 10 cm -0 d = 15 cm y X
The air in the reservoir has an absolute pressure of 450 kPa and a temperature of 30°C. The throat has a diameter of 50 mm. (Figure 1) Figure 50 mm 1 of 1 Part A Determine the greatest possible mass flow through the nozzle. Express your answer using three significant figures. m = Submit VAΣo↓vec Provide Feedback Request Answer ? kg/s Next >
If the velocity profile between two infinite parallel plates is given by: Uy 1 др (y2 - yH)+ H u = 2и дх Use this expression for air flowing between the two plates with a pressure gradient -20 Pa / m. and distance between the plates are 6 mm. ind the velocity of the upper plate in each the following case: a- The shear stress at the upper plates is zero. b- The shear stress at the lower plates is zero. c- The flow rate is zero. d- The velocity at y = 2 mm is 1 m/ s. Use dynamic viscosity = 1.8 x 10-5 kg / (m.s)
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.
The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of 18 m/s, and out the pipe at B and C with the same velocity v. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mm at A, and at B and C the diameter is 25 mm. pw = 1000 kg/m³. (Figure 1) Figure v B 22 A 18 m/s Part A Determine the component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. F₂ = Submit Part B F₁ = Submit μA Value Request Answer Determine the y component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. Provide Feedback μA Value S Units Request Answer Review Units Next >
plzzzzz help me i neeed the answer
A 100-mm diameter jet of water is discharging from a nozzle into the air at a velocity of 36 m/s. the nozzle is inclined at an angle of 25 degrees with horizontal. neglecting air ressistance, determine: 1. the elevation of the highest point with respect to a datum at the tip of nozzle. 2. the area of the jet at the highest point of the stream.
An airplane is in level flight at low altitude, so that atmospheric pressure and densities are 1 atm and 1 kg/m3, respectively. There is a Pitot tube attached to the airplane, so that air entering the tube stagnates at the rear of the tube. The stagnation pressure is measured to be 1.45 x 105PA. What is the speed of the airplane?