100 mm Consider the propeller tube shown in The density of air is Pa = 1.23 kg/m. The diameter of the nozzles at B, C, D, and Eis 100 mm 0.5 m M 60 rad/s 0.5 m 0.5 m 05 m Part A If the propeller tube rotates at a constant rate of 60 rad/s when 1.80 kg/s of air enters at A, determine the frictional torque M acting on the tube. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise.

100 mm Consider the propeller tube shown in The density of air is Pa = 1.23 kg/m. The diameter of the nozzles at B, C, D, and Eis 100 mm 0.5 m M 60 rad/s 0.5 m 0.5 m 05 m Part A If the propeller tube rotates at a constant rate of 60 rad/s when 1.80 kg/s of air enters at A, determine the frictional torque M acting on the tube. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A straight horizontal pipe 100 mm in diameter terminates in a short, tapering nozzle from which a jet of water 50 mm in diameter is discharged to atmosphere. If the gauge pressure immediately before the nozzle is 50 kPa and friction in the nozzle is negligible, calculate the tensile force between the nozzle and pipe.
Plz solve correctly
A centrifugal pump impeller delivers 4000 gal/min ofwater at 20 ° C with a shaft rotation rate of 1750 r/min.Neglect losses. If r 1 =6 in, r 2 = 14 in, b 1 = b 2 =1.75 in,V t 1 = 10 ft/s, and V t 2 = 110 ft/s, compute the absolutevelocities ( a ) V 1 and ( b ) V 2 and ( c ) the horsepower required.( d ) Compare with the ideal horsepower required.
Subject :Fluid mechanics Give me right solution. Help me urgent
The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at outlet is 18 mm. A pump, which runs at 16.6 rev/s, is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre; the friction loss in the suction pipe is 68 Q² meter and that in the delivery pipe is 650 Q² meter where Q in m3/s is the rate of flow. The blades themselves occupy 5% of the circumference and are backward facing at 35° to the tangent. At inlet, the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and shock losses in the pump, the velocity heads in the suction and delivery pipes are negligible, calculate the following: The flow rate, m3/s, of the pump. Manometric efficiency, in %, of the pump.
Q//Determine the shaft power required for the pump to produce the flow shown in the figure . The efficiency is 80% and the losses may be neglected. The nozzle area 25cm2.
A fire hydrant supplies water under a pressure of 190 kPa. A 100-mm-diameter hose is connected to it at A and the hose extends 40 m to the fire truck inlet at B. B Part A Determine the pressure of the water as it arrives at B. The friction loss is 1.5 m for every 10 m of hose. The inlet at Bis 0.5 m higher than the hydrant outlet. Express your answer to three significant figures and include the appropriate units.
A certain turbine has a capacity of 45 ft³/s. 3ft³/s is lost during the flow. The tailwater is 14 7 ft from the center of the turbine. The intake measures 35 in and the pressure is measured by mercury u-tube manometer which measures 15.566 ft in the intake and 3.00 ft in the discharge side. The datum of the scale is at 5.62 ft below that of the center of the turbine. The brake power output was 767.8 kw. Losses is measured to be 20.2 KW. Calculate the efficiency of the turbine
Calculate the velocity values in the D and E sections of the system in the figure. AE/AD= 3, Z1=1.6 m and Z2=0.2 m. The mercury deviation in the manometer is Z3=0.4 m. (Friction effects will be neglected, γmercury=13.6 t/m3 , γwater=1 t/m3).
Help with this practice question
A fluid flows through the pipe below from left to right. The speed at point P is V1. If the speed at point Q is V2, which of the answers below is correct? • P radius R radius 2R Ov2 = V1 OV2 = 2 V1 OV2 = 8 V1 OV2 = 4 V1
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.