Question 3 Water enters a U-shape pipe at 50 kg/s mass flow rate at inlet 1 and leaves the U-shape pipe in the angles shown at 40 kg/s and 10 kg/s at outlets 2 and 3, respectively. The total volume of the pipe is 2.2x10-3 m3 and the density of water is 1000 kg/m³. The pressures at points 1, 2 and 3 are 10 kg/s 0=45 3 cm 40 kg/s 10 cm ૭] 300kPa, 200kPa and 100kPa (atmospheric), respectively. What are 50 kg/s 5 cm the forces needed in the horizontal and vertical directions to hold this pipe in place?

Question 3 Water enters a U-shape pipe at 50 kg/s mass flow rate at inlet 1 and leaves the U-shape pipe in the angles shown at 40 kg/s and 10 kg/s at outlets 2 and 3, respectively. The total volume of the pipe is 2.2x10-3 m3 and the density of water is 1000 kg/m³. The pressures at points 1, 2 and 3 are 10 kg/s 0=45 3 cm 40 kg/s 10 cm ૭] 300kPa, 200kPa and 100kPa (atmospheric), respectively. What are 50 kg/s 5 cm the forces needed in the horizontal and vertical directions to hold this pipe in place?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 7 WATER FLOWS IN A PIPE OF CONSTANT CROSS AREA 5 CM. THE PIPE IS BENT AT 90° AS SHOWN IN THE FIGURE…

Q: Consider the following compressor that receives air at a constant rate of three cubic feet per…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: h0=2.4 mρ=1000 kg/m3Qi=0.24 m3/sQo=0.01 m3/st=100 sA=5 m2

Q: Water at 10°C flows through the system shown in the figure below at 0.28 m³/s. Energy loss in the…

A: Temperature of the water vessel. T1=10°C Diameter of the pipe. d =30cm=0.3m Diameter of the pipe…

Q: Water enters a cylindrical tank through two pipes at rates of 141 and 126 gal/min (see the figure…

A: Water enters a cylindrical tank through two pipes at the following rates:Q1= 126 gal/min = 0.2807…

Q: Fluid flows into a junction at a flowrate Q, and exits via two pipes of equal diameter, as shown in…

Q: Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations…

Q: A pipe of diameter 11 cm conveying 200 liters/s of water has bend of angle (θ = 90⁰ if last digit is…

A: Given:D=11 cm =0.11 mQ=200 L/s =200*10-3 m3/sθ=90°P1=15 N/cm2 =1510-4N/m2 or PaP2=10 N/cm2 =1010-4…

Concept explainers

Hydronics

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: Finding forces needed in the horizontal and vertical directions to hold this pipe in place:

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A U-shaped tube is filled with water of density 1000 kg/m3 until the level of the liquid is 28 cm above the bottom of the tube. Then oil of specific gravity 0.78 is poured into one branch of the tube until the level of the liquid in the other branch is 34 cm above the bottom of the tube. (g=9.8m/s2) I) Find the level of the oil-water interface in the branch where the oil was spilled II) Find the level of the oil-air interface in the branch where the oil was spilled
Please solve it quickly I am at the exam
0.95 m3/sec flow rate of water flows downwards in a pipe as shown in figure. If the pressures at points 1 and 2 are to be equal. Determine the diameter of the pipe at point 2.The velocity at point 1 is 6.5 m/sec and the diameter of pipe at point 1 is 330 mm. The height between point 1 and point 2 is 2.8 m?
The pressure in a water tower is 20,674 Pascals (N/m2) higher than at an open faucet. The density of water is 1000 Kg/m3. Use Bernoulli’s equation to determine the velocity of outflow from the open faucet. If the height difference between the top water level in the tower and the faucet is 7.2 meters, then the velocity of outflow is ROUND TO 3 DECIMAL PLACES
AT. 2] a water pump is to be used in a water supply system as shown in the figure. The pressure at point 1 is 70 kPaa and the pressure at point 2 is 101 kPaa. The velocity in the 60-mm pipe is 2 m/s. Find the pump power. Neglect friction, and assume no change of internal energy of the water and no heat transfer between point 1 and 2. Take the density of water at standard condition. 2 m2 10 m Pump
could you please help me calculate theheigth in metres of the fluid at time t= 100s
Water flows in pipes A and B and converges into pipe C as shown in the figure. If the flow rate at pipe C is 50 L/s and the velocity at pipe A is 4 m/s, determine the velocity (in m/s) of water at pipe B. da = 100 mm dc = 300 mm B dB = 200 mm a. 0.019 b.0.031 c.0.592 d.0.707 The 75-mm water main pipe in your street has a pressure of 200 kPa and carries 25 lps of flow. You want to store water into an elevated tank, 12 m above the water main, so there is adequate flow in your 3rd level bathroom. Assume the total losses from the water main to the water tank is 10 m. Determine the rated power (in kW) of a household pump required if the pump has an efficiency of 80% and the air pressure in the partially full tank is 300 kPa. The flow through the pump is 3 lps. a.6.00 b.1.12 c.9.37 d.0.72
How do I answer this question?
Methane in the gaseous state flows at a rate of 0.072 m^3/s in a pipe at a temperature of 27°C and gauge pressure of 148.675kPa (point 1). The pipe is divided into two branches (point 2 and 3), as seen in the figure. If the exit velocity in pipe 3 is 12 m/s with a density of 1.9 kg/m^3, what is the flow rate and velocity in pipe 2? Consider that in section 2 the fluid is leaving with a temperature of 402°C and an absolute pressure of 175 kPa. We have an atmospheric pressure of 101.325 kPa and R_methane = 0.5182 kJ/kg ⚫K. (1) Inflow D1 D3=50mm D2=100mm (3) (2)
The material distorts into the dashed position shown. Determine the average normal strains Px, Py and the shear strain gxy at A, and the average normal strain along line BE.
Water enters a 5-L tank at a rate of 4.00 kg/s and is withdrawn from the tank at a rate of 6.00 kg/s. The tank is initially four-fifths full. (a) Write a mass balance for this process by assigning a variable function to the mass of water at time t. Describe the terms that are present in the balance; give reasons for deletion of any terms. (b) Solve the balance to find how long it will take the tank to drain completely.