Q1.1 (v6q9-15) An air-standard cycle with variable specific heats is executed in a closed system and is composed of the following four processes: 1-2 isentropic compression from 100kPa and 27C to 800 kPa; 2-3 v=constant heat addition to 1800K; 3-4 isentropic expansion to 100kPa; 4-1 p=constant heat rejection to initial state. (a) Show the cycle on p-v and T-s diagrams. (b) Calculate the net work output per unit mass. (c) Determine the thermal efficiency. Ans: 570.1 kJ/kg, 51.9%

Q1.1 (v6q9-15) An air-standard cycle with variable specific heats is executed in a closed system and is composed of the following four processes: 1-2 isentropic compression from 100kPa and 27C to 800 kPa; 2-3 v=constant heat addition to 1800K; 3-4 isentropic expansion to 100kPa; 4-1 p=constant heat rejection to initial state. (a) Show the cycle on p-v and T-s diagrams. (b) Calculate the net work output per unit mass. (c) Determine the thermal efficiency. Ans: 570.1 kJ/kg, 51.9%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A medium size power station is used to produce 30 MW net power for a refinery. The station uses steam as the operating fluid and operates according to the Carnot cycle between the pressure limits of 0.4 bar and 35 bar. Steam enters the boiler as a saturated liquid and leaves it as a dry saturated vapour. (vii) Using the highest and lowest temperature values in the cycle, recalculate the efficiency of the cycle and show that it is equivalent to the result in part (vi). (viii) Calculate the thermal efficiency of the power station if the isentropic efficiency of the steam turbine is 94%. (ix) State main disadvantages of using the Carnot cycle as the basis for a power station. (x) State the name of the cycle that is used in practice in power stations, along with three key benefits over the Carnot cycle.
THERMODYNAMICS Consider an air-standard Otto cycle with a heat addition of 800 Btu/bm of air, a compression ratio of 7, and a pressure and temperature at the start of the compression process of 13 lbf/in2, 50 F to simulate an actual spark-ignition engine. Determine the maximum pressure and temperature of the cycle, the thermal efficiency of the cycle, and the mean effective pressure assuming the variation of specific heat with the value from table A-19E Show Complete solution on a paper.
An ideal gas Diesel engine, that has an inlet temperature, pressure and compression ratio of 22 0C and 102 kPa 21:1 respectively. The maximum cycle temperature is 1,276 0C. Take Specific heat at constant pressure and constant volume for air as 1.005 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the specific heat rejected during the cycle to one decimal place and include the correct SI unit.
Required information Problem 09.015 - 3-Step Air-Standard Cycle with Constant Specific Heats - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS An air-standard cycle with constant specific heats at room temperature is executed in a closed system with 0.003 kg of air and consists of the following three processes: 1-2 v= Constant heat addition from 95 kPa and 17°C to 380 kPa 2-3 Isentropic expansion to 95 kPa 3-1 P = Constant heat rejection to initial state The properties of air at room temperature are cp = 1.005 kJ/kg-K, cy= 0.718 kJ/kg-K, and k = 1.4. Problem 09.015.b - Net Work for Constant Heat Capacity Air-Standard Cycle Calculate the net work per cycle, in kJ. (You must provide an answer before moving on to the next part.) The net work per cycle is kJ.
H.W2: An air-standard Carnot cycle is executed in a closed system between the temperature limits of 350 and 1200 K. The pressures before and after the isothermal compression are 150 and 300 kPa, respectively. If the net work output per cycle is 0.5 kJ, determine (a) the maximum pressure in the cycle, (b) the heat transfer to air, and (c) the mass of air. Assume variable specific heats for air. Answers: (a) 30,013 kPa, (b) 0.706 kJ, (c) 0.00296 kg
Determine the efficiency of a constant volume cycle withlexpansion ratio equal to 7.8. **Express final answer in TWO DECIMAL PLACES Do not round off in between solution. Type only the "numerical value". No need to include the unit and percent sign. Answer:
There are supplied 400 kJ per cycle to an ideal diesel engine operating on 0.5 kg of air. At the beginning of compression, pressure is 100 kPa and temperature is 50 degrees Celsius. At the end of compression, pressure is 4000 kPa. Determine the ff: Compression ratio t2, t3, V3, P4, t4 in degree Celsius, m³ and kPa Heat rejected in kJ Network in kJ Thermal efficiency, % MEP in kPa
On the diagram below sketch a basic Rankine cycle with superheating. Assume that there are irrevesibilities in the turbine and pump. Identify the device associate with each process. Make sure to label: the states and include important features, e.g. lines of constant temperature, volume, pressure, entropy, vapor dome, etc.
Can you briefly define the Stirling cycle and write down its biggest message?
At the beginning of compression in the otto engine cycle, P1= 101.35 kPa, T1 = 21 deg.C and Vi = 0.113 m². At the end of the compression process the pressure is 551.58 kPa. If 174.5 kJ/kg are added during the constant volume reversible. Heating process and the values of k and R for air are 1.4 and 0.287 kJ/kg.deg.K respectively. 2. a. Draw the P-V Diagram b. Draw the T-S Diagram c. Find the temperature at the end of compression d. Find the temperature at the beginning of expansion e. Find Heat removed f. Find the compression ratio g. Find the thermal efficiency
In a standard Brayton cycle, the maximum temperature is 1,419 K while the minimum temperature is 299 K. The heat added during the isobaric process is 1,096 kJ/kg. Determine the thermal efficiency in %. Use two decimal places in the final answer.
In a constant volume cycle, the pressure at the end of compression is 10 times that at the start, the temperature limits are 20 ° C and 1900 ° C. Determine i. Compression ratio, ii. Thermal efficiency and iii. Work done. Take R = 287 J/kg K, y = 1.4