Q1. The structure shown in the sketch is used to pull a load. The force that the load exerts at point D is 300 lb in the direction shown in the figure. Points A,B and C are pin connections. Find: a) The internal loadings acting on the cross section E-E'. Section E-E' is perpendicular to the longitudinal axis of bar AD. b) If the cross sectional area of bar AD is 2 in2 find the average normal stress and the average shear stress 241

Q1. The structure shown in the sketch is used to pull a load. The force that the load exerts at point D is 300 lb in the direction shown in the figure. Points A,B and C are pin connections. Find: a) The internal loadings acting on the cross section E-E'. Section E-E' is perpendicular to the longitudinal axis of bar AD. b) If the cross sectional area of bar AD is 2 in2 find the average normal stress and the average shear stress 241

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate: a) the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.
EXAMPLE: II. 2 ft Show the V-M diagram using Area Method of the following beam: R₂ 200 lb/ft 4 ft - Hinge 2 ft
:>
Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm
4) Take that W₂= 3.8 kN/m intensity for the distributed load below. The fixed support at O can have support reactions with a vertical and horizontal force and a moment. B) Answers: A) Show your free body diagram with the resultant loads, their locations and indicate the support reactions. Mo = Ox= -3 m- Oy = Wo 1.5 m- What are the support reactions at the fixed support at O?
Solve step by step in digitl format
Question 1) For the beam whose loading condition is given in the figure, the force F is F = 18 kN , the distributed load w is w = 10 kN / m , the moment M is M = 14 kN.m and the length L is L= 9 m . According to this; M kN.m w kN/m F kN 3 В L Question 1-A) Find the support reactionat point A in the x direction (A x ). (Enter your result as kN without writing units.) Question 1-B) Find the support reaction at point A in y direction (A y). (Enter your result as kN without writing units.) Question 1-C) Find the support reaction in the y direction ( B y) at the B point . (Enter your result as kN without writing units.)
A rod of length L 1.79 m is attached to a wall. The load on the rod increases linearly (as shown by the arrows in the figure) from zero at the left end to W = Wall 235.0 N/m at the right end. Find the shear force at a) the right end, Submit Answer Tries 0/12 b) the center, and Submit Answer Tries 0/12 c) the left end. -L W
Downloads/CW507-CW538-CW568-2-19S-%20Aircraft%20Structures%20Fundamentals.pdf (D Page view A Read aloud V Draw E Highlight ++ Question 4: The frame consists of right-angled triangles of base 2 m with angles as shown in Figure Q4. It is supported vertically at pins F and D and is subjected to the loading shown at pins A, B and C. (a) Determine the support reaction at F and D. (b) Use the method of joints to determine the type (tension or compression) and the magnitude of the force in each member of the frame. 30 kN 40 kN B 20 kN 60° 90° 60° 90° 60° D Figure Q4 (25 marks) SW 2020
The maximum break stress of the chain ring seen in the figure on the side is 420 N/mm2, since the diameter of the rod is 8 mm, find the load it can carry as daN. (π=3,14)