Q1. In the experiment of the mechanical equivalent of heat, a 203 g aluminum cylinder experiences a temperature rise by 1° C by turning the crank a number of turns. If the specific heat of aluminum is 0.22 cal/g. C (a) how much neat was absorbed by the cylinder? (b) What force is responsible for heating the cylinder?

Q1. In the experiment of the mechanical equivalent of heat, a 203 g aluminum cylinder experiences a temperature rise by 1° C by turning the crank a number of turns. If the specific heat of aluminum is 0.22 cal/g. C (a) how much neat was absorbed by the cylinder? (b) What force is responsible for heating the cylinder?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

QUESTION 9 During the video on heat conduction, H through a single pane window was calculated. Now, consider a window that has wo panes with a 6 mm air gap between them. Each pane has an area of 1.9 m. The window separates the inside of a house at 22 °C from the outside at 0°C. Let Kair = 0.03 W/(m-K). Hint: This problem can be simplified by noting that the thermal conductivity of glass is much greater than air, so the effect of the glass on the total conductivity can be ignored. Therefore, the purpose of the two glass panes is to support the layer of air between them. Calculate the heat current H through the double glass pane window in watts. Do not include units in your answer and state your numerical answer in normal form. QUESTION 10 Consider process 3 in the figure below (or in First_Exam_Figures.pdf) shown by the bold solid line with an arrowhead. The pressure of a gas is decreased at constant volume. V. Click Save and Submit to save and submit. Click Save All Ansuers to save all…
Q2: A hot concrete slab comes from a furnace at an inatial temperature of 85
An insulated beaker with negligible mass contains liquid water with a mass of 0.235 kg and a temperature of 72.2 °C. ▼ Part A How much ice at a temperature of -21.4 °C must be dropped into the water so that the final temperature of the system will be 32.0 °C ? Take the specific heat of liquid water to be 4190 J/kg. K, the specific heat of ice to be 2100 J/kg. K, and the heat of fusion for water to be 3.34x105 J/kg . ► View Available Hint(s) mice = 0.096 Submit VE ΑΣΦ Provide Feedback Previous Answers www X Incorrect; Try Again; 5 attempts remaining kg Next >
parts d & e only
1. Will dumping heat into a system necessarily raise the temperature of the system? Explain. A gold pillar has a height of 3.00m when the temperature is -20.0°C. How much is the change in the height of the pillar when the temperature is +20.0°C? (See the equation 2. sheet for the properties of gold.)
0 F2 W S 9. A 44.0-kg block of ice at 0°C is sliding on a horizontal surface. The initial speed of the ice is 7.80 m/s and the final speed is 4.00 m/s. Assume that the part of the block that melts has a very small mass and that all the heat generated by kinetic friction goes into the block of ice. Determine the mass of ice that melts into water at 0°C. grams #3 3 X 20 F3 E D ASA $ C 200 F4 R F er de % 5 V F5 T G MacBook Air B ... F6 Y & 7 H F7 U N CO * 8 J DIL F8 - M 9 K F9 O V O H F10 PEL 000 Р C I F11 + F12 ?
H78
2. In an experimental set-up, 5 kg of salt solution is heated in a glass vessel by a 159 W power gas burner. The internal energy of the solution is to be increased from 90 kJ/kg to 178 kJ/kg for a certain amount of time. An electric stirrer is used to ensure uniform heating of solutions, the power consumption of the stirrer is 30w. The rate of heat loss from the vessel 50o W. How many minutes was the solution heated if the motor is 80% efficient?
13. Solve
The initial temperature of 150 g of ice is -20°C. The spe-cific heat capacity of ice is 0.5 cal/g.C° and water's is1 cal/g•C°. The latent heat of fusion of water is 80 cal/g.a.How much heat is required to raisethe ice to 0°C andcompletely melt the ice?b. How much additional heat is required to heat the water(obtained by melting the ice) to 25°C?C.What is the total heat that must be added to convert the80 g of ice at-20°C to water at +25°C?d. Can we find this total heat simply by computing howmuch heat is required to melt the ice and adding theamount of heat required to raise the temperature of 80 gof water by 45°C? Explain
Q14
0.4 kg water is at room temperature 23 degrees in an aluminum container. An unknown metal with 0.5 kg mass is placed inside the water raising its temperature to 40 degrees. A)What is the specific heat of the unknown metal. B) Would the equilibrium temperature greater, less or the same if the system was not properly isolated.