Q1. 220V, 200, 100mH are represents data information for a two-level VSI feeds an inductive load. If the output frequency of the inverter is 50HZ, calculate: a- Instantaneous load current. b- Average supply current. c- Load rms voltage and current. d- The average and peak transistor and diode currents. e- Sketch the input and the output current waveforms.

Q1. 220V, 200, 100mH are represents data information for a two-level VSI feeds an inductive load. If the output frequency of the inverter is 50HZ, calculate: a- Instantaneous load current. b- Average supply current. c- Load rms voltage and current. d- The average and peak transistor and diode currents. e- Sketch the input and the output current waveforms.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Summarise the production of silicon wafer and transistor.
1. With Neat sketch explain the construction, operation, VI characteristics, application and features of the power semiconductor device which is having asymmetric voltage blocking capability.
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 10 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1000 and N2 is given as 800, compute for the primary peak voltage. V(Volts) D1 D2 v2 * D3 * D4 (seconds) Note: Put answers on the blanks and also upload your answers as PDF file in the Moodle Final Exam submission link. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is 2. The value of the dc voltage (Vdc) in volts is 3. The value of the ripple factor is 4. The value of dc current (ldc) in amperes is 5. The value of the output peak voltage (Vpout) in volts is 6. The value of…
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 12 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, de voltage and ripple factor. If the load resistance has a value of 7 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage. A01 D2 A D3 D4
At high levels of gate current, the characteristics of an SCR approach those of what semiconductor device? a. MOSFET b. BJT c. JFET d. Diode
In the following circuit, the nMOS has a threshold voltage of Vr = 1.0 Vand K = 2 mA/VÅlso given that R1 = 3 kNVpp identical with vp. = 0.9(i.e. use CVD model for the diodes). Our task is to set the value of Rp such that the MOSFET will be operating at the edge of saturation. What's edge of saturation? We know in the triode region vps vGs – VrHence, the edge of saturation means when vps = vGS - VAt this mode, both the equations for In in saturation mode and triode mode would give the exact 6 Vand the diodes are same result, VDD VDD Rp R1 KIKKH
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
7
i.Explain the operation of a Zener diode as voltage regulator? ii.Explain why the BC junction of an NPN transistor is reversed biased?
Dive into the fabrication process of microchips. What are the key steps involved, and how are transistors created on a silicon wafer?
2.
1. With Neat sketch explain the construction, operation, VI characteristics, application and features of the power semiconductor device which is having asymmetric voltage blocking capability.