For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 10 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1000 and N2 is given as 800, compute for the primary peak voltage.

For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 10 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1000 and N2 is given as 800, compute for the primary peak voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

with steps please..
a) Draw energy band diagram of a pn junction in thermal equilibrium showing the energy bands in the neutral p and n regions and in the space charge region. b) Draw the space charge density in a uniformly doped pn junction assuming abrupt junction approximation. c) Draw a graph showing the potential variation through the space charge region of uniformly doped pn junction. d) Draw the rectified sinusoidal output waveforms for the full-wave rectifier with a smoothing capacitor showing sections of the waveform where the capacitor char
UTM system. (a) Describe their different function and operation in the DC supply system. UTM (b) Can zener replace the function of the regular diode in the application described in a DC power supply A UTM in question 3(a)? Justify your answer. TM UTM UTM 2.UTM UTM UTM 5 UTM UTM UTM & UTM & UTM UTM &UTM UTM TM UTM & UTM UTM
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
A sinusoidal voltage of 48v, 60 Hz is applied to a half - wave rectifier with dynamic resistance of the diode of .001ohms, turns ratio (3:1). Calculate the DC and RMS currents flowing through the load (R=250ohms). Also calculate the dc output power developed, ac - input power supplied, rectification efficiency and ripple factor.
Q1: Draw the circuit of full wave rectifier mentioned on the circuit all equipment requirements to measure input and output voltages and the circuit current take in consideration voltage source 100v rms and load of 15k2 and device required to draw output signal, find the following: a. Calculate output current and voltages. b. Find input and output powers and the efficiency. c. Draw input and output voltages and output currents mentioned the amplitudes. d. What is the PIV of full wave bridge rectifier? And how many types of full wave rectifiers?
An intrinsic semiconductor is neither a good conductor nor a good insulator. Select one: O True O False A varactor is a pn junction diode that always operates in reverse-bias and is doped to maximize the inherent capacitance of the depletion region. Select one: O True O False A simple diode rectifier has 'ripples' in the output wave which makes it unsuitable as a DC source. To overcor this on e can use
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 12 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, de voltage and ripple factor. If the load resistance has a value of 7 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage. A01 D2 A D3 D4
Rectifier circuit...
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
a) Draw energy band diagram of a pn junction in thermal equilibrium showing the energy bands in the neutral p and n regions and in the space charge region. b) Draw the space charge density in a uniformly doped pn junction assuming abrupt junction approximation. c) Draw a graph showing the potential variation through the space charge region of uniformly doped pn junction. d) Draw the rectified sinusoidal output waveforms for the full-wave rectifier with a smoothing capacitor showing sections of the waveform where the capacitor char