Q1 ]: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown in Fig. Q1. If the normal stress in each rod must be limited to 275 MN/m². (a) find the minimum diameter required for each rod. (b) if the L₁ = 115 mm and L2 = 105 mm, compute the total deformation of the rod, the modulus of elasticity E = 60 GN/m². 130 kN 65 kN A -d₁ 130 kN B

Q1 ]: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown in Fig. Q1. If the normal stress in each rod must be limited to 275 MN/m². (a) find the minimum diameter required for each rod. (b) if the L₁ = 115 mm and L2 = 105 mm, compute the total deformation of the rod, the modulus of elasticity E = 60 GN/m². 130 kN 65 kN A -d₁ 130 kN B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

L2 (2) B LI (1) Figure-4 The member ABC is subjected to forces as shown in Figure-4. The member is made of a material with an elasticity modulus of 98 GPa. The segment (1) and segment (2) have diameters of 46 and 30 mm, respectively. If F=29 kN, L1=1 m, L2=1,1 m; Determine the magnitude ofP (kN) such that the deflection of C is zero. Determine the normal stress (MPa) in segment (2). If it is compressive stress, use - sign. Determine the deformation (mm) of segment (2). If it is negative deformation, use - sign. Determine the normal strain of segment (2). If it is negative deformation, use - sign.
A steel rod with a cross-sectional area of 2.5 square inches is stretched between two fixed points. The rod is stress free at 70 degrees Fahrenheit. What will be the stress at zero degrees Fahrenheit? Use α = 6.5 x 10^-6 per degree Fahrenheit and E = 29 x 10^6 psi
A bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 110 kN, P2 = 230 kN & P4 = 160 kN. Also, determine the stresses in each section & the net change in the length of steel bar. square of size a1=60mm, L1=34 cm, size a2 = 35mm, L2=36 cm, size a3=60 mm & L3 =31 cm Take E = 173 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
A bar ABC length L consists of two parts of equal lengths but different diameters.Segment AB has diameter dt=100 mm,and segment BC has diameter d2 = 60 mm.Both segments have a length B2=0.6 m.A longitudinal hole of diameter d is drilled through segment AB for one half of its length (distance L/4 = 0.3 m).The bar is made plastic having a module of elasticity E=4.0 GPa.Comprssive loads P = 110 KN act at the ends of the bar. (a) If the shortening of the bar is limited to 8.0 mm.What is the maximum allowable diameter dma of the hole? (see the figure part a.) (b) Now if daxx is instead set at p1/2 . at what distanc h from end c should load P be applied to limit the bar shortening to 8.0 mm?(see the figure part b) (c) Finally if loads t are applied at the ends and "mm is the permissible length.v of the hole if shortening is to be limited to 8.0 mm?(see the figure part c)
4-Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 50 mm x 31 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 22 kN (tensile), 30 kN (compressive), 22 kN (compressive) respectively. Take E as 100 GPa, Poisson’s ratio as 0.3 The stress along length direction (Unit in MN/m2)= _____________ The compressive stress along width direction (Unit in MN/m2)= _____________ The compressive stress along depth direction (Unit in MN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget FBD AND show me your step Please make sure your answer is correct please
3. A steel rod of 3 cm diameter and 5 m length is connected to two grips and the rod is held at a temperature of 95 °C. Determine the stress in the rod, and the force in the rod if the temperature drops to 30 °C for the following cases a. The grip ends do not yield b. The grip ends yield by 0.12 cm Assume the Young's Modulus of the rod is E = 2×105 MPa, and the CTE is a=12×106/ °C
2. Two steel cables support an applied load of 100 kN as shown in the figure below. Determine the following: a. The deformation of member AC and member BC. b. The vertical and horizontal displacement of point C. A A = 75 sq. mm L = 3 m E = 200 GPa 22° C 45° 18° A = 75 sq. mm В L = 3 m 100 kN E = 200 GPa %3D
Simple stressa nd strain problem! Pleasee help
AB and CD caps of the same material are tightly fitted on both ends of the 24 mm diameter AD steel bar. a) Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the extension amount of BC part by the force P you found. Take the elastic modulus E = 200 GPa. 36mm 24mmr 36mm 48mm D 28mm
Figure Q4 (a) shows an L-bracket ABC with diameter d which lies in the horizontal plane. It is made from a material with elastic and shear moduli E and G, respectively. If a vertical load P is applied at end C, determine the total strain energy that is stored in the whole structure. Express your answer in terms of P, E, G, d and L. Neglect the strain energy due to shear force.
Two hard rubber blocks with Modulus of Rigidity equal to 350 kPa are used in an anti-vibration mount to support a small machine as shown below. Let a = 20 mm, b = 50 mm and c = 80 mm. Deterrmine: (a) the shearing strain in the rubber blocks when a downward deflection of 6.50 mm occurs due to P. (b) the magnitude of P. Include the figure showing the shearng strain and the FBD to support your force equation, (if there is any). Show the step by step solution.