shows an L-bracket ABC with diameter d which lies in the horizontal plane. It is made from a material with elastic and shear moduli E and G, respectively. If a vertical load P is applied at end C, determine the total strain energy that is stored

Q: A cube of side 40 mm, subjected to 3 mutually perpendicular tensile forces of 9 kN, 5 kN, 5 kN…

A:

Q: Four axial forces are applied to the 25mm thick structural steel bar with 40mm diameter pins as…

A: for solution refer below images,

Q: A rectangular bar of length L has a slot in the central half of its length. The bar has width b,…

A: Write the given data.Determine:- The overall the elongation of the bar

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: Given: The initial diameter of the rod is d=5 mm. The Young's modulus of material is E=120 MPa. The…

Q: Q2 Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium. Brass and Steel,…

A:

Q: A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. The…

A: Step 1: Given data: Length of circular rod L=200 mm. Diameter of circular rod D=20 mm. Axial force…

Q: Why As is like 2(pi/4)d^2 This question asks for the average tension only in section a-a, is that…

A: As we can see that section a-a will be in shear and not in tension.

Q: A mass is set on a sqaure box made of polymer. It deforms as shown in following picture. Calculate…

A: Given that, L=12 m,a=4 m,b=1 m, Since the box is square, so∠XOY=90°,

Q: Consider a linear rectangular thin sheet of metal, subjected to uniform uniaxial tensile stress of…

A: A linear rectangular thin sheet of metal, subjected to a uniform uniaxial tensile stress of 100 MPa…

Q: A copper wire of length (400+R) cm , diameter of (4+R) mm and mass of (5000 + R) g, if Young's…

A:

Q: Find the tensile stress in the rod having a diameter of 25 mm subjected to a tensile load of 500 N.…

A: Given, Diameter of rod = d = 25 mm Tensile load = P = 500 N Young's modulus = E = 200 GPa = 200 x…

Q: (B) – Figure Q4/B show the bone has an outer rac of 15 mm and thickness 3 mm. Determine the strains…

A: Draw the diagram for the axes given in the problem. Understand that in the given figure, the shaft…

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the…

A:

Q: uniform diameter d = 1.75 in. Segment (1) is an aluminum ₁ = 10000 ksi Segment (2) is a copper Ę₂ =…

A:

Q: The beam is supported by two wires AB and CD that have a diameter of 12 mm and 8 mm, respectively as…

A:

Q: find the axial strain

A: Given; Young modulus =100 GPaPoisson's ratio=0.3 Find axial strain of the container material ?

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

A:

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

A:

Q: Figure Q1 shows a composite rod ABC attached in between two rigid walls. Part AB is a solid rod made…

A:

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

A:

Q: block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in…

A:

Q: rod ABC is applied with axial loading as shown in Figure Q4(a). Using E = 200 GPa, determine (i) the…

A: Given:E=200 GPaP=36 KNd=16 mmD=20 mmLAB=600 mmLBC=900 mm

Q: Q4 /B/ The stress-strain curve for four materials are shown in figure below. Which material…

A: From the stress - strain curve for the material C, it is observed that material C undergoes a large…

Q: Determine the total deformation of the steel rod shown in figure under the given loads. Take the…

A:

Q: 2) The bar shown has a cross-sectional area of 0.001 m² and a modulus of elasticity of 100 GPa. It…

A: The cross sectional area is .The modulus of elasticity is .The axial uniformly distributed load is…

Q: A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress…

A: The strain values are given as, ε1=121×10-6ε2=304×10-6ε3=203×10-6 The Poisson's ratio is given…

Q: A 1.9-m-long rigid bar AD is pinned to a wall at A and connected to two wires at B and C as shown in…

A: Given data: The length of the bar AD is L = 1.9 m. The clockwise rotation of the bar AD is θ=3°.

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: P 50 mm 100 mm 200 mm 0.09 mm B unloaded E A Rigid D 150 mm C 300 mm

A:

Q: stress component oy is

A: From the given fig;Strain in the Z -direction is 0Yield strength in uniaxial tension of material of…

Q: A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical…

A: Given data: ◆ The normal strain in the rod (1): ε1 = -1380 µm/m = -1380 × 10-6 m/m ◆ The gap in the…

Q: OF = 5712 N

A: Calculate linear strain with the given data

Q: Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A:

Q: Q1. A simple bar element is shown below. It is initially horizontal, with length L. Under some…

A: INTRODUCTION : The distortion of the body caused by the application of a load or force is known as…

Q: Find the internal normal stress in all relevant segments of the bar in the picture. The bar has a…

A:

Q: 2.12 The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.