Q1) The diodes in the circuit in Fig.1 have piecewise linear parameters of Vy = 0.6 V and rf = 0. Determine the output voltage Vo and the currents ID1, ID2, ID3 and I for the following inputconditions: (a) V1 V2=0 (b) V1 = V2 = 5 V (c) V1 5 V, V2 = 0 (d) V1 = 5 V, V2 = 2 V. 0.5 ΚΩ V₁OW IDI 0.5 ΚΩ D2 V₂0- www D₁ ID2 Fig.1 ID3 +10 V 9.5 ΚΩ D3 +5 V OVO

Q1) The diodes in the circuit in Fig.1 have piecewise linear parameters of Vy = 0.6 V and rf = 0. Determine the output voltage Vo and the currents ID1, ID2, ID3 and I for the following inputconditions: (a) V1 V2=0 (b) V1 = V2 = 5 V (c) V1 5 V, V2 = 0 (d) V1 = 5 V, V2 = 2 V. 0.5 ΚΩ V₁OW IDI 0.5 ΚΩ D2 V₂0- www D₁ ID2 Fig.1 ID3 +10 V 9.5 ΚΩ D3 +5 V OVO

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the following limiter consider that both zener diodes are identical with Vz = 4.5V @ lz =20mA and rz = 502. Also assume that the zener diodes will have a constant voltage drop of 0.75 V when forward-biased. R Z, Z a) Find the value of R such that the positive and negative limits are +5V when the input reaches ±10V. b) Sketch and label the voltage transfer characteristic for input voltages between ±10 V.
Using the ideal diode model, find the output voltage for the input voltage of the following circuit and graph it in detail. (a) (b) R₁ D₁ www ww R3 D2 (a) R₁ D₁ www + + D2 R2 vo Vo R₂ (b)
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C = 300µF placed in parallel with the load resistor RL = 1KN and Vm = 15V. Assume that the diodes are piece-wise linear with r,= 100 and V, 0.7V then derive the plot for the output voltage across the load resistor RL. Plot A V Plot C V wm Plot B V Plot D V please pick a plot
*Use 4 decimal places. For the circuit below, determine the diode voltages VD1 and Vp2, diode currents Ip1 and Ip2, and voltage across the resistor, VRLIMIT- Use ideal model. Assume r'd (for both diodes)=200. Note D, is Germanium, D2 is Silicon, VBIAS = 14V and RLIMIT = 760 ohms . VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; Ip = Blank 4 mA ; VRUMIT = Blank 5 V ... Capture3.JPG +Vp1- +VRLIMIT- +Vp2- Ip2 BIAS
Q1. The input voltage V, is a sinusoidal voltage with maximum value of 9 (if it is 0, then assume that Vi MAx = 10 V ). If the threshold voltage of the diodes is 0.1 V, plot Vo versus V,. +10 V 10 k2 v - O vo 10 k2 10 k2 -10 V
After solving a circuit with ideal diodes (Vf=0), what check is necessary for diodes initially assumed to be on? Off? We must check to see that reverse voltage appears across all diodes assumed to be on, and we must check to see that forward current flows in diodes assumed to be off We must check to see that forward current flows in diodes assumed to be on, and we must check to see that reverse voltage appears across all diodes assumed to be off
In the circuit shown below, R1 = R2 = 200Q, and the two diodes are identical with VD = 0.7V and Vps =5V. 1. Find output voltage Vo. 2. Find I1, I2, Ipi and Ip2. R1 www Vo Ipi Ip2 Vps
3. In the following circuits, given source voltage Vs=9V, R1, R2 and R3 all are 1kOhms. Answer the questions by considering the diodes as ideal and practical silicon ones respectively. Vs Vs Vs R2 R2 R2 Vout P D R1 R1 R3 R1 (a) Vout = ? (b) Vp = ? (c) Vp = ? Note: Vp means the voltage at point p. w
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
What voltage is boosted at the output of a multiplier. a) average b) rms c) peak d) instantaneous Which assumption is not used in the analysis of multipliers? a) a capacitor will not discharge b) start with the cycle of the source that will forward bias the nearest diode c) the output will always be multiplied d) a single diode is forward biased at a time A voltage multiplier a) multiplies the output voltage b) has very high voltage and low current c) can employ inductors d) may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations at a) the input and output b) the load c) source d) in the environment Between a lower percent regulation and a higher one, which is better? a) lower b) higher
For the subsequent questions, please refer to the circuit below. Assume that the diode is ideal (e.g. the voltage across it is zero volts when it is ON) IK VINZI IN=IV (+) I Sv(t Jo Vo Suppose we assume the diode is ON, what is V. in volts? Suppose we assume the diode is ON, what is the resistor current I in mA? Suppose we assume the diode is ON, our assumption is correct because the condition ID>=0 will hold as lp will be (in mA)... Suppose we assume the diode is OFF, this is a wrong assumption because when we solve for Vp with the diode as an open-circuit, the condition VD<=0 will NOT hold as Vp will be (in volts)...