Answered: Q1/ For the assembly below, determine…

Q1/ For the assembly below, determine the average normal stress for the cable. Assume that the cable has a diameter of 10 mm. take P =12 kN. B 0.1 m 0.5 m C -0.75 m -0.75 m- -0.75 m-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the nodal displacements and the element stresses. E = 105 GPa, v = 0.3, and t = 5 mm. You don't have to calculate everything manually, but can write a code to get some input from you and find the stiffness matrices for instance. 400 mm 3 5 400 mm 30 kN 2
QI/ Three stresses acting on fold F1, F2 and F3 1- Resolved the forceces (FI, F2 and F3) into components 2- Eplain the deformation if: FI = F2 FI #F2 F2 F1 F3
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
The screw of the clamp exerts a compressive force of 500 lb on the woodblocks. Sketch the stress distribution along section a–a of the clamp. The cross section is rectangular, 0.75 in. by 0.50 in.
At the nodes in the truss system given in the figure occurring displacement and the stress and reaction that occurs Find the forces.E=200GpaA=10000mm2
Find the stresses in cables a and b.
Based on the figure below, a pin supports a bar at Z and a cable supports X to Y around W. Determine the stress in the cable in megapascal with a diameter of 0.68 inch and a weight of 1,550 pounds. a = = 1 ft b= 3 ft c = 10 ft X bft Y W aft cft Z
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 9 mm in diameter. Assume a = 590 mm, b = 295 mm, h = 360 mm, and 0= 60°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h a ● b
Find the stresses in each section and total change in length of the bar as shown in figure. The bar is subjected to an axial pull of 24 kN. Take the diameter of section 1 as 56 mm, length L1 as 44 mm, ,the dimensions of section 2 as 65 mm x 63 mm, L2 as 16 mm, section 3 is a square of size 30 mm, length L3 as 50 mm. Also take the Young’s modulus of sections as E1 = 2.1x105 N/mm2, E2 = 1.1x105 N/mm2, E3 = 0.75x105 N/mm2 (i) Stress in section 1 (unit in N/mm2) is = Answer for part 1 (ii) Stress in section 2 (unit in N/mm2) is = Answer for part 2 (iii) Stress in section 3 (unit in N/mm2) is = Answer for part 3 (iv) Total Change in length of the given bar (unit in mm) is =
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1
The uniform 300-1b bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B and the 0.5-in. diameter cable CD. Find the stress in the cable. DRAW THE FREE BODY DIAGRAM.