Answered: Q1/ Determine the resulting…

Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2= 12x106/°C, AT= 35 °C, h= 1200 mm, 0 = 60° (1) (2) B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Values are m= 360mm n= 375mm q= 24mm r= 18mm P= 0.6kN
In the system, the AB and BC rod is made of the pipe whose cross-section is given in the figure. σemn = 85 MPa. For this loading case .......... (σ Since AB account value), AB bar is .......... (suitable / not suitable) and .......... (σBC account value) so BC bar is ... (suitable / not suitable). Even if the pipes are suitable, shaft diameters are required if one wishes to be changed. The diameter of the AB shaft must be at least .......... mm and the diameter of the BC shaft must be at least .......... mm. F=34 kN , D=34 mm , d=17 mm , θ=(28,5)^0
Construct the reduced stiffiness matrix of the shown truss, Fig. 3.Then determine the nodal displacements and the nodal forces in clement 3. L(1) L(2) 2 m, L(3) 2/2, A(1)- A(2) = A(3) = 80 mm2, and E= 200 GPa. |1 (1) 2 2 kN '3 kN (2) 45° (3) 3 Fig. 3
Soil Bearing Capacity A square column foundation has to carry a gross allowable load of 1605 kN (FS = 3). Given: Dƒ = 1.7 m, y = 15.9 kN/m°, ø' = 34°, and c' = 0. Use Terzaghi's equation to determine the size of the foundation (B). Assume general shear failure. For ø' = 34°, N, = 36.5 and N, = 38.04. %3D (Enter your answer to three significant figures.) B = 4.
E=210GPa; L=400mm; A=2.5Cm²; F1-400N; F2= -600N for the numerical application F2- F1 L 1.5 L 2A A L A
66 ll ? e V:09 The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m D. 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm², E = 200GPA, a = 15x106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change. -200 mm- - 80 mm- A 0f B "Rigid" |(1) (2) 250 mm
We have an assembly with a steel rod AB and an aluminum BC, each having a cross sectional area shown in Figure 2. If the assembly is subjected to axial loadings at point A and B shown in Figure 1, Determine the displacement of rod BC and the deformation of rod AB. The original length of each rod is shown in Figure 1. Show manual integration for area under the parabola must be shown E. = 200 GPa. Ed = 70 GPa
Please answer number 1 with step by step solution. I Need the answer immediately .
3. If only one person is on the swing in the image below, it is comparable to a point load of F = 500 N placed at x = 0.5 m on a wooden branch embedded at one end (cantilever). The length of the branch is 1.5 m. It is given that I = 1 × 10-6 m² and E = 2x 10° Nm². The boundary conditions are y(0) = 0, y'(0) = 0 , y'"(0) = M and y''(0) = –2M. Use your notes to model the fourth order differential equation suited to this application. Present you differential equation with y'' subject of the equation. Use the Laplace transform to solve this equation in terms of M. Use your solution to determine the value of M at x = 0.5 m where this branch will break (deflection more L than thresh y 2 240 ). Do not use Matlab as its solution will not be identifiable in the solution entry. You must indicate in your solution: 1. The simplified differential equation in terms of the deflection y you will be solving 2. The simplified Laplace transform of this equation where you have made L{y} subject of the…