Q1: Determine the length, angle of contact, and width of a 9.75 mm thickleather belt required to transmit 15 kW from a motor running at 900 r.p.m. Thediameter of the driving pulley of the motor is 300 mm. The driven pulley runs at300 r.p.m. and the distance between the centers of two pulleys is 3 meters. Thedensity of the leather is 1000 kg/m³. The maximum allowable stress in theleather is 2.5 MPa. The coefficient of friction between the leather and pulley is0.3. Assume open belt drive.

1: Calculate the Velocity of the BeltThe velocity (v) of the belt is calculated…

Answered: Q1: Determine the length, angle of…

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

QI: A shaft carries four masses in parallel planes A, B, C and D in this order along its length. The masses at B and C are 18 kg and 12.5 kg respectively, and each has an eccentricity of 60 mm. The masses at A and D have an eccentricity of 80 mm. The angle between the masses at B and C is 100° and that between the masses at B and A is 190°, both being measured in the same direction. The axial distance between the planes A and B is 100 mm and that between B and C is 200 mm. If the shaft is in complete dynamic balance, determine: 1. The magnitude of the masses at A and D; 2. the distance between planes A and D ; and 3. the angular position of the mass at D.
Determine the mechanical advantage of the following pulley system. Provide your answer in kg to 4 decimal places. В A Answer:
novig size modestib Beri N 1-12 12- 60° 37. A block-and-tackle pulley hoist is suspended in a warehouse ay by ropes of lengths 2 m and 3 m. The hoist weighs 350 N. The ropes, fastened at different heights, make angles of 50° and th 38° with the horizontal. Find the tension in each rope and the magnitude of each tension. 50° brd 60° 2 m 38° 3 m 501001 hon sit 44. 45 4
#4?
1. Determine the equivalent spring stiffness constant of the following. 150 N/m 240 N/m 60 N/m wwwwwww 290 N/m 105 N/m wwwwww 35 N/m a. 250 N/m www 145 N/m F Ans:
i need the answer quickly
4. Find the width of the belt, necessary to transmit 7.5 kW to a pulley 300 mm diameter, if the pulley makes 1600 r.p.m and the coefficient of friction between the belt and the pulley is 0.22. Assume the angle of contact as 210° and the maximum tension in the belt is not to exceed 8 N/mm width. [Ans. 67.4 mm]
1- Water vapor at a flow rate of 20000 kg / hour enters a steam boiler with a specific volume of 150 kPa 0.001053 m3 / kg. With the energy it takes from the fuel in the combustion chamber of the boiler, it rises at 150˚C at 1200 kPa. If the boiler has poor insulation and loses 100 kW of heat to the environment, calculate the time required to increase 1 ton of water to 150 ° C in the boiler. A. 347 sB. 3752 sC. 1651 sD. 648 sE. 2494 s
Determine the output pressure of a compressor operating with the following data: a. Actual power required to drive the compressor is 20 kW. b. Overall efficiency of the compressor is 75%. c. Compressor delivers four standard m3/min. d. Compressor inlet pressure is 100 kPa abs. Please use the equation in the picture to solve it.
1–2. Figure C1.2 shows a mechanism that is typical in the tank of a water closet. Note that flapper C is hollow and filled with trapped air. Carefully examine the configuration of the components in the mechanism. Then answer the following leading questions to gain insight into the operation of the mechanism. 1. As the handle A is rotated counterclockwise, what is the motion of flapper C? 2. When flapper C is raised, what effect is seen? 3. When flapper C is lifted, it tends to remain in an upward position for a period of time. What causes this tendency to keep the flapper lifted? 4. When will this tendency (to keep flapper C lifted) cease Plz connect me if you want to explan subject for me .... +962 79180149 Thx
Find T.F to the mechanical system below? K 0000 S M Riy
A 40lb weight is stretched to the end of a spring. The spring is stretched 6in. Find the displacement from equilibrium of the weight after pi/8 seconds, if the weight is released from rest at 10 inches above the equilibrium. round to the nearest tenth of a foot.

SEE MORE QUESTIONS

Recommended textbooks for you

Refrigeration and Air Conditioning Technology (Mi…

Mechanical Engineering

ISBN:

9781305578296

Author:

John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:

Cengage Learning