Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular plate of size 0.75m x 0.55 m and an inclined plane with angle of inclination 45' as shown in figure 1. The weight of the rectangular plate is 0.5 kN and it slides down the inclined plane with a uniform velocity of 0.35 m/s. The thickness of oil film is 1.75 mm. Then, state the scope for this obtained viscosity? Recangdar plabe -oil Inclined plane Figure 1

Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular plate of size 0.75m x 0.55 m and an inclined plane with angle of inclination 45' as shown in figure 1. The weight of the rectangular plate is 0.5 kN and it slides down the inclined plane with a uniform velocity of 0.35 m/s. The thickness of oil film is 1.75 mm. Then, state the scope for this obtained viscosity? Recangdar plabe -oil Inclined plane Figure 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: In falling ball viscometer experiment, the viscometer with a calibration factor K=0.3 is used to…

A: As per given question Given data Calibration factor=0.3 Density of oil=0.8 gr/cm^3 Density of ball…

Q: Fluid mechanics question Solve and please provide correct answers An oil of viscosity 0.02 Ns/m2 is…

Q: For the conic body shown in Figure (3) which rotating with constant angular velocity of 12 rad/s,…

Q: If the viscosity is 0.0144 stokes what is the equivalent kinematic viscosity in m^2/s? (answer in…

A: Kinematic viscosity is the Ratio of dynamic viscosity and density of fluid. CGS units are stokes SI…

Q: Q1 A smooth cylinder of 50.1 mm inside diameter and 150 m long is placed with its axis vertical. If…

Q: With free body diagram. Clear and complete solution please thank you. 1. A square block weighing…

Q: A 3d block with the dimensions of 50cm by 30cm by 20cm and a weight of 450 N, is going to be moved…

Q: The apparatus shown in the figure is to coat a thin steel plate with oil. using for. Fluid1 has a…

Q: A plate of area 2.15 m is pulled with a speed of 0.3 m/s relative to another plate located at 3.5 mm…

Q: What is the shear force that acts on the circumference of the piston (N)?

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given data diameter of shaft (d) = 250 mm diameter of sleeve (D) = 251 mm Power required = 2204 W N…

Q: Figure 1 shows a box of mass m that is supported on a surface inclined at angle 0 to the horizontal.…

Q: A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both…

Q: Figure 1 shows a layer of oil(8.95 kN/m^3),

Q: Two parallel flat plates are spaced 2 in. apart. One plate is moving at a velocity of 10 ft/min and…

Q: An iron block with dimensions of 0.25x0.25x0.25 m; It slides over an inclined plane with an…

A: V=0.25m×0.25m×0.25mθ=30ot=0.0069mm=6.96×10-6 mμ=7.5mPa s=7.5×10-3 Pa-sρ=7800 kg/m3

Q: With free body diagram please thank you. Clear and complete solution please. 1. A square block…

A: Given Data- Weight W=1.1KN Side lenght a=250mm Thickness of film =6μm Viscosity=7mPa-s We have to…

Q: Falling Sphere Viscometer Given: Inner diameter of cylindrical tube = 0.03 m…

Q: What methods exist to calculate the viscosity of dense gases and liquids?

A: Viscosity: It is defined as the resistance or opposition offered by liquid to the flow. When there…

Q: Question 1. The apparatus shown in the figure is used to coat a thin steel plate with oil. Fluid1 is…

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of…

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.052 poise and kinematic viscosity of…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subpart of a question. Please post…

Q: Q2) ) If the vertical component of the hydrostatic force on the gate BC shown in fig.2 is 1200 kN…

A: Assume that width of the gate is w and vertical component of force act on face BC is 1200kN . So…

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

Q: A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø) containing oil…

A: Given Specific gravity, SG = 0.84 Kinematic viscosity = 7.1x10-6 m2/sec Diameter, D…

Q: PROBLEM 2.0 Determine the viscosity of a fluid having kinematic viscosity 6 stokes and specific…

A: Given data: kinematic viscosityv=6 stokesSG=1.9 Need to determine the viscosity of the fluid.

Q: You are working in a machine tool manufacturing industry for the project to design CNC control…

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given data: The height of the lubricant is

Q: If the box has a constant area of (0.2 m“), what is its terminal speed?

Q: lunger having diameter of 10 inch slides in a 10.006 inch diameter of a cylinder, the annular space…

A: In the question we have,kinematic viscosityϑ=0.004 ft2/sDiameter of plungerdp=10 inchDiameter of…

Q: A flat area 1.5x106mm² is pulled with a speed of 0.4m/s relative to another plate located at a…

A: Given data: A=1.5×106 mm2=159×10-6 m2du=0.4 m/sdy=0.15 mmμ=1 poise=0.1 Pa.s Need to determine the…

Q: PROBLEM 1.0 A flat area 1.5x10mm² is pulled with a speed of 0.4m/s relative to another plate located…

Q: List the various types of fluid. Define kinematic viscosity and compressibility. Note the expression…

A: Fluid: A substance that can flow is called as fluid. Fluid Types: There are several types of fluids…

Q: A body weighing 77 lb with a flat surface area of 8 ft2 slides down a lubricated inclined plane…

Q: = Define and state the viscosity equation for a Coutte flow. 2: Develop and algebraic equation for…

A: The Coutte flow refers, to the fluid flow between two plates where the lower plate is fixed and the…

Q: A group of students designed a model drone with a scaling of 1:20 and tested it in a wind tunnel.…

A: Given data, The scale of the model drone is 1:20 So, LPLm=20 Velocity of the model, i.e., velocity…

Q: (b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the…

A: Given: The kinematic viscosity of the model is 1/3 of the kinematic viscosity of the prototype.…

Q: the Newton's law of viscosity with one CAum (b) Calculate the pressure difference (in kPa) between…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Q1: Calculate the dynamic viscosity of an oil, which is used for lubrication between a rectangular plate of size 0.75m x 0.55 m and an inclined
plane with angle of inclination 45' as shown in figure 1. The weight of the rectangular plate is 0.5 kN and it slides down the inclined plane with
a uniform velocity of 0.35 m/s. The thickness of oil film is 1.75 mm. Then, state the scope for this obtained viscosity?
Recangdar plabe
-oil
Inclined plane
Figure 1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

B1. Determine the kinematic viscosity of the fluid between the plates as shown in Figure B1 given the following information: F = 5N h = 0.5mm v = 7m/s L=21 cm w = 10cm SG= 0.80 Moving plate Stationary plate Fluid Figure B1 V
The viscosity of motor oil is 4.79× 10-³ N. s/m², motor oil is used as a lubricant between two machine parts. The variation in velocity of the oil is 1.6 m/s and a maximum shear stress is 62.8 N/m². What is the required spacing between machine parts in millimeter?
Problem 3: A honeybee farmer wants to measure the absolute viscosity of his honey. You suggest dropping a 4mm steel ball into a container of honey and measure the time it takes for the ball to pass between two marks as shown. If the time is 13 seconds, what is the honey's viscosity. Assume the density of the honey is 1450 kg/m3 and the density of the steel ball is 7800 kg/m³. Honey 5 cm
plz help me with this one , i would appreciate it if you can help me now. A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that has a diameter of 1 m that filled with oil that has a viscosity of 8x10-3 N.s/m2 What is the shear force that acts on the circumference of the piston (N)? Assume the variation in velocity of the oil is linear.
Answer the problem with complete solutions. Refer to the conversion factor given
An airplane that has a cross-sectional diameter D = 4 m of the front portion is to fly at a speed of 600 km/hr in air that has a density of 1.1 kg/m and dynamic viscosity of 1.27 x 10 Pa.s. A small size model of scale ratio (1/17) to be tested in a different fluid that has a dynamic viscosity 5 x 105 Pa .s and a density of 500 kg/m2. It is determined that the parameters that are important for this test are: diameter D, density, viscosity, velocity V, the length of the wings L and the drag force F. What must be the speed (m/s) of the model to Choose... ensure dynamical similitude? What must be the corresponding diameter of the model (cm)? Choose.. What is the number/s of dimensionless groups for this problem? Choose...
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
Please solve it quickly
Question 1: An ( 8 Kg ) box slides down a ( 20°) inclined plane while lubricated by a ( 2 mm ) thick film of oil having a kinematic viscosity of ( 5.176 Stoke ) and a specific gravity of ( 0.85 ). If the box has a constant area of (0.2 m´), what is its terminal speed?
Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant clearance. If the power required to rotate the shaft is 2204 watts, find the viscosity (N.sec/m?) of lubricant oil in the clearance. Take length of sleeve as 150 mm.