Q1: Beam AB, BC, CD are pin-connected at B and C. Knowing that the allowable normal stress is (110) MPa in tension and (-150) MPa in compression and the section modulus is (258.6×106 m³ and 87.47×106 m³) for top and bottom respectively, determine: A) The largest permissible value of (w) if beam BC is not overstressed. B) The corresponding maximum distance (a) for which the cantilever beams AB and CD are not overstressed. 12.5 mm tw -200 mm- 150 'mm

Q1: Beam AB, BC, CD are pin-connected at B and C. Knowing that the allowable normal stress is (110) MPa in tension and (-150) MPa in compression and the section modulus is (258.6×106 m³ and 87.47×106 m³) for top and bottom respectively, determine: A) The largest permissible value of (w) if beam BC is not overstressed. B) The corresponding maximum distance (a) for which the cantilever beams AB and CD are not overstressed. 12.5 mm tw -200 mm- 150 'mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the column wooden section with 3.5 m in length Fixed at both ends. Use the given allowable stress below. The beam carries a Axial load of 85 KN. Use Square Section 1. Compressive Stress Parallel to Grain = 15 MPa 2. Modulus of Elasticity = 14000 MPa
Kindly answer. Thank you!
A solid circular column is 3 meters long. It is fixed at the bottom and pinned at the top. The Youngs modulus of the material is 70 GPa and the maximum allowable stress is 25 MPa. Using a factor of safety of 2.5 in calculating Eulers critical load: i. Determine the dimensions of the cross section if the column is to safely support a 100 kN load. i. Confirm the normal stress developed in the column and comment on the result.
UNCRACKED ANALYSIS ON BEAMS DETAILED SOLUTION PLS.
1.1 A stainless steel tube with an outside diameter of 60 mm and a wall thickness of 5 mm is used as a compression member. If the normal stress in the member must be limited to 200 MPa, determine the maximum load P that the member can support.
QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
HW: For the cracked beam of details shown in Figure, check the bending stress. mm WD-10 kN/m WL= 12 kN/m working stress Design method 5 m 3020mm 450 mm Q+ 170 mm 250 mm
1. Determine the following: a. Determine the moment of inertia of the section about its neutral axis. b. Maximum tensile stress in the beam c. Maximum compressive stress in the beam 300 N/m 625 mm T: 100 mm 500 mm A B 3 m 1.5 m 100 mm
A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
1. The overhang beam has a composite cross section as given below. Determine the maximum compressive and tensile stresses at the beam cross section due to the forces acting on the beam. Draw the stress distribution along the height of the cross stresses. (E=5000 MPa) 24 kN 18 kN/m 9 cm C x 30cm AB A 6.00 m 9cm +9㎝ +9㎝ 9cmt cm -1.50m