Q1:-Answer the following statements with (True) or (False), only) 1-The Bernoulli's equation is a relation between pressure, velocity and area of Crosse section. 2- The one objective of Bernoulli experiment is to verify Bernoulli's equation by using a venture meter to observe fluid elevation through the tube with different flow rates. 3- Typically value of coefficient discharge for orifice meter range from (60-68) %. 4- When the coefficient of discharge of negative relationship with coefficient of contraction. 5- The objectives flow measuring by orifice meter is determining the discharge of coefficients only. 6- The losses in the iron material are less than the losses in the plastic material.

Q1:-Answer the following statements with (True) or (False), only) 1-The Bernoulli's equation is a relation between pressure, velocity and area of Crosse section. 2- The one objective of Bernoulli experiment is to verify Bernoulli's equation by using a venture meter to observe fluid elevation through the tube with different flow rates. 3- Typically value of coefficient discharge for orifice meter range from (60-68) %. 4- When the coefficient of discharge of negative relationship with coefficient of contraction. 5- The objectives flow measuring by orifice meter is determining the discharge of coefficients only. 6- The losses in the iron material are less than the losses in the plastic material.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A docs.google.com/forms/d/e/1FAlpQLSetk8UE/ PROBLEM 6: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3 * Oil SG = 0.79 P gage = 260 kPa Gasoline SG= 0.70 Pipe Air 45 cm 50 cm 22 cm 10 cm Mercury SG= 13.6 Water Your answer
An orifice meter is a device used to determine the flow velocity and flow rate in a pipe. The meter is connected to a U-tube manometer shown in Figure 2(a). The meter is connected to a U-tube manometer shown in Figure 2(b). Derive the equation for the flow rate, Q in the horizontal pipe.
Q-4 The apparatus shown in the figure is used to measure the velocity of air at the center of a duct having a 10 cm diameter. A tube mounted at the center of the duct has a 2 mm diameter and is attached to one leg of a slant-tube manometer. A pressure tap in the wall of the duct is connected to the other end of the slant-tube manometer. The well of 10 cm p = 150 kPa the slant-tube manometer is sufficiently large that the elevation of the fluid in it does not change significantly when fluid moves up the leg of T= 20°C the manometer. The air in the duct is at a temperature of 20°C, and the pressure is 150 kPa. The manometer liquid has a specific gravity 30 of 0.7, and the slope of the leg is 30°. When there is no flow in the duct, the liquid surface in the manometer lies at 2.3 cm on the slanted scale. When there is flow in the duct, the liquid moves up to 6.7 cm on the slanted scale. Find the velocity of the air in the duct. Assuming a uniform velocity profile in the duct, calculate the…
(Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the pipe contraction shown in the figure below. The flowing fluid is water, and viscous effects are negligible. Determine the two manometer readings, h and H. V=1.7 ft/s h = H= 6.4 in. Air ↓ SG= 1.10 ft ft TH 3.8 in.
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft3. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.5 lb/in². h = ft
Q. Determine the kinematic viscosity at the average temperature and determine the Reynolds number and type of flow using the data shown below and table values: Data obatined from a Reynolds Number test: Water temperature at the beginning of the experiment = 25 oC Water temperature at the end of the experiment = 30 oC The Volume of water collected in 25 seconds = 240 ml Pipe diameter, d= 10 mm. (use eq'n reynold's number, Re = VD/v
d) The viscosity of a fluid is to be measured using a viscometer constructed of two 750 mm long concentric cylinders. The outer diameter of the inner cylinder is 150 mm and the gap between the two cylinders is 1.2 mm. The inner cylinder is rotated at 200 rpm and the torque is measured to be 10 Nm. a) Derive a generals expression for the viscosity of a fluid using this type of viscometer, and; b) Determine the viscosity of the fluid for the experiment above. Shaft е -Cylinder - Velocity Profile
1) A manometer is attached to two pipes as shown. If knowing mercury SG is 13.6, sea water SG is 1.035, and fresh water p is 1,000 kg/m³, determine the pressure difference between two pipelines at the centers. Fresh Water h. -60 cm Air hair -70 cm hea <- 40 cm Mercury Sea Water hi -10 cm
A centrifugal pump is used to pump a liquid in steady turbulent flow through a smooth pipe from one tank to another. Develop an expression for the system total head Δh in terms of the static heads on the discharge and suction sides zd and zs respectively, the gas pressures above the tanks on the discharge and suction sides pd and Ps respectively, the liquid density ρ, the liquid dynamic viscosity μ, the gravitational acceleration g, the total equivalent lengths on the discharge and suction sides (∑Le)d and (∑Le)srespectively, and the volumetric flow rate Q.
A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg =13.55). On one side of the tube, oil (SG=1.4) was trapped, a bubble formed, and the fluid inside was stationary. The volume of the oil was 0.6 in^3 and the volume of the air was 0.2 in^3. Now, the oil and bubble are removed. The pressure change across the air bubble is negligible and any curvature on the bubble surface can be neglected in calculating the volumes. Determine how much the mercury height rises (i.e. h 4 -h 2 ).
Current Attempt in Progress A U-tube manometer is connected to a closed tank as shown in the figure below. The air pressure in the tank is 0.50 psi and the liquid in the tank is oil (y = 54.0 lb/ft³). The pressure at point A is 2.00 psi. Determine: (a) the depth of oil, z, and (b) the differential reading, h, on the manometer. (a) z = (b) h = ft ft Air Oil SG = 3.01 2.0ft + Open h