Q1/ A thick wall consists two layers of Gypsum, insulation and brick as shown in figure below. The ambient temperature is 20 °C and heat transfer coefficient is 5 W/m2. K in the left side. The surface temperature of right side is 45 °C. find the heat losses per meter length. What will happen if the insulation's thickness * .increases by 25% Gypsum k = 0.04W/m. K T = 45 °C h =5 W/m'. K T = 20 °C 1 cm 2 cm 1 cm Insulation k=0.04W/m. K Brick k=0.69 W/m. K

Q1/ A thick wall consists two layers of Gypsum, insulation and brick as shown in figure below. The ambient temperature is 20 °C and heat transfer coefficient is 5 W/m2. K in the left side. The surface temperature of right side is 45 °C. find the heat losses per meter length. What will happen if the insulation's thickness * .increases by 25% Gypsum k = 0.04W/m. K T = 45 °C h =5 W/m'. K T = 20 °C 1 cm 2 cm 1 cm Insulation k=0.04W/m. K Brick k=0.69 W/m. K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please include a fbd of the problem
A slab of thickness L = 0.1 m and of thermal conductivity k = 1 W/mK has the temperature distribution as T(x) = ax2 + bx + c. The boundary conditions; insulation at at x = L and a 100 W/m2 constant heat flux at x = 0. What is the temperature at the insulated surface if c = 5 °C?
As shown in the sketh below, a steam pipe of 0.12-m inside diameter is insulated with a layer of calcium silicate. "2. Ta2} 1. Ta,1} Steam Insulation (a) If the insulation is 10 mm thick and its inner and outer surfaces are maintained at T, = 800 K and Ta = 490 K. respectively,. what is the rate of heat loss per unit length (q) of the pipe, in W/m? (b) Determine the rate of heat loss per unit length (d), in W/m, and outer surface temperature T,2, in K, for the steam pipe with the Inner surface temperature fixed at T = 800 K, inner radius = 0.06 m, and outer radius n = 0.18 m. The outer surface is exposed to an airflow (T 25°C) that maintains a convection coefficient of h = 25 W/m2-K and to large surroundings for which Tur = T, = 25°C. The surface emissivity of calcium silicate is approximately 0.8.
I need the answer as soon as possible
A long rod with a thermal conductivity of 1 W/m K subject to the given boundary conditions. in the permanent regime temperature distribution with the energy balance method for ∆x=∆y= 0.2m find it. In addition, the unit of heat transfer between the rod and the fluid. Calculate for length.
solve this problem and dont reject it plzz
An external wall of a building has a U value of 0.50 W/m^2K. The indoor temperature is21 degrees C and the outdoor temperature is -2.0 degrees C The steady-state heat loss is calculated to be 11.5W/m^2 The wall contains a layer of insulation 40 mm thick with a conductivity of0.035 W/mK. What would the insulation thickness need to be in order toreduce the steady state heat loss by 50%? answer = 0.11m please show all working
Need help on the Q.
Answer correctly and quickly as possible please.
The fin shown in Figure is insulated on the perimeter. The left end has a constant temperature of 100 °C. A positive heat flux of q = 5000 W/m² acts on the right end. Let Ky = 10 W/(m °C) and cross-sectional area A = 0.1 m2 Determine the temperatures at L/4, L/2, 3L/4, and L, where L = 0.8 m. 4-0.1 m T-100 C 5000 W/m
A house has a composite wall of wood, fiberglass insulation and plaster board, as indicated in Figure 2.1. The total wall surface area is 300 m²" h = 30 W/m°K Tni = 20°C | h. = 60 W/m²K Teo =-15°C Fiberglass L=10 cm Plaster board k= 0.04 W/mK L=1 cm k = 0.15 W/mK Plywood L-2 cm k= 0.13 W/mK Figure 2.1 (i) Represent the composite wall by a thermal circuit, and label all the components in the circuit ii) Determine the inner surface temperature of the house.
A square steel bar of side length w = 0.21 m has a thermal conductivity of k = 15.6 J/(s⋅m⋅°C) and is L = 2.7 m long. One end is placed near a blowtorch so that the temperature is T1 = 95° C while the other end rests on a block of ice so that the temperature is a constant T2. a. input an expression for the heat transferred to the cold end of the bar as a function of time using A=w^2 as the cross-sectional area of the bar. b. how much energy in joules was conducted in 1 hour, assuming t2=0*C c. input an expression for the mass of the water melted in one hour using Q1 from above and Lf in the latent heat of fusion. mw=