Q1// A double-cage of a 3-phase, 50-Hz, 4-pole induction motor, have the followingequivalent circuit parameters, all of which are phase values referred to the stator and thestator impedance is negligible:Outer cage Ro' = 99Xo' = 252Inner cage R' = 25X₁' = 851- Calculate the ratio of torques produced by outer cage and inner cage at starting.2- If the motor runs at 1425 rpm and the rotor input phase voltage is 230 V, calculate thetoque in synchronous watt per phaseTo3- What slip will the torque contributed by the two cages be equal?

It is given that: f=50HzP=4V=230 VNr=1425 rpmOuter cage:Ro'=9Ω Xo'=2ΩInner cage:Ri'=2Ω Xi'=8Ω

Q1// A double-cage of a 3-phase, 50-Hz, 4-pole induction motor, have the following equivalent circuit parameters, all of which are phase values referred to the stator and the stator impedance is negligible: Outer cage Ro'=9 Xo' = 252 Inner cage R' = 25 X₁' = 82 1- Calculate the ratio of torques produced by outer cage and inner cage at starting. 2- If the motor runs at 1425 rpm and the rotor input phase voltage is 230 V, calculate the toque in synchronous watt per phase To = Ti 3- What slip will the torque contributed by the two cages be equal?

Q1// A double-cage of a 3-phase, 50-Hz, 4-pole induction motor, have the following equivalent circuit parameters, all of which are phase values referred to the stator and the stator impedance is negligible: Outer cage Ro'=9 Xo' = 252 Inner cage R' = 25 X₁' = 82 1- Calculate the ratio of torques produced by outer cage and inner cage at starting. 2- If the motor runs at 1425 rpm and the rotor input phase voltage is 230 V, calculate the toque in synchronous watt per phase To = Ti 3- What slip will the torque contributed by the two cages be equal?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Induct.motor.
i need the answer quickly
Q2. A 230 V single-phase induction motor, 50 Hz, has the following winding impedances (at rest): Zm=28 <70° Q. Za=42 <45°Q A) Calculate the input current at start-up. B) Obtain the amount of capacitor in series with the auxiliary winding for which the torque Maximum startup. Then compare the input current, auxiliary winding current and torque all at start-up in two modes with and without starter capacitor.
We make( V/F) constant in speed control of three-phase induction motor in order to make motor torque constant? * True False
The stator resistance of a 1-phase induction motor is 2.5 ohm and its leakage reactance is 2.0 ohm. Onno-load, the motor takes 4 A at 96 V and at 0.25 lagging power factor. The no-load friction andwindage loss is negligible. Under the blocked-rotor condition, the input power is 130 W at 6 A and42 V. obtain the equivalent circuit parameters.
12. The IR-compensation in frequency control of induction motors is used for: a) compensation of the voltage drop in the active resistance of the stator winding. b) compensation of the voltage drop in the inductive reactance of the stator winding. c) keeping the motor voltage constant. d) keeping the motor speed constant U₁ U₁ Us0 0 f. f₁
1.
Question A 3-phase, 415 V, 4-pole, 50 Hz induction motor draws 5 times the rated current at rated voltage at starting. It is required to bring down the starting current from the supply to 2 times of the rated current using a 3-phase autotransformer. If the magnetizing impedance of the induction motor and no-load current of the autotransformer is neglected, then the transformation ratio of the autotransformer is given by
g) What is an advantage if the starting Torque of the induction motor is higher than the nominal load Torque? h) What are the main differences when the equivalent circuits of transformer and asynchronous motor are examined?
Answer it right..
32. The star connected rotor of a a 3-phase induction motor has a resistance and standstill reactance of 0.4 ohms/phase and 2.5 ohm/phase respectively. The emf induced between slip rings at stand still is 80 V, the stator being connected to small supply voltage. Find the rotor current and power factor at starting current when the rings are (i) short circuited (ii) joined to a star star-connected resistance of 5 ohm/phase.