The equivalent circuit per-phase parameters for a 220 V, 50 Hz, three-phase, star-connected, 4-pole, induction motor is: R1 = 0.22 02, R2' = 0.15 0. The inductor motor has a slip of 4% and the full load current has a magnitude of 61 A. The mechanical losses (windage and friction) and the iron losses are 610 W are 420 W respectively. The input power is 36300 W. Determine the following when the motor operates at full load at rated speed: A. the synchronous speed RPM B. the rotor speed in RPM C. the efficiency of the motor in percentage.

The equivalent circuit per-phase parameters for a 220 V, 50 Hz, three-phase, star-connected, 4-pole, induction motor is: R1 = 0.22 02, R2' = 0.15 0. The inductor motor has a slip of 4% and the full load current has a magnitude of 61 A. The mechanical losses (windage and friction) and the iron losses are 610 W are 420 W respectively. The input power is 36300 W. Determine the following when the motor operates at full load at rated speed: A. the synchronous speed RPM B. the rotor speed in RPM C. the efficiency of the motor in percentage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solver 200/5A Is=2.75A Ip=?
30. If D1 were to open what would be the effect on the output voltage? _DROP_ A. Voltage would that 20V UNREG. 100 R1 DI 10V 1200 Your BROW
S I ID 5 V Vo Given that Vin is 7V: a. What is ID if the diode is on? b. What is Vo if the diode is off? What is VD if the diode is off? C.
With a neat diagram ,explain about the working of 4 bit R-2R ladder Type DAC.
Part C
Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two approaches
b (i) in photo please, using the diagram and answering question b (i)
With the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is germanium, how much is the output voltage in volts on the negative half cycle? (put polarity (+ or -) and values only) Vpcin) V out RL
Please in typing format please ASAP for Thanks ?
answer fast
Scimal value of the value that will occur at the ADC output. (ADC is 12 Question 2 MN is the last two g160100555 - yu digits of In an analog measurement operation set as an external reference, the reference source of the ADC is a voltage source of 5 analog input, write the g160100555-Gu Aumber your student 010055 g160100555 - Yu 9441 20100 g160100555- Y 44 s0100538 g160100555 - Y 944 201005 g160100 2447 .5Volts. In case of 3.5V voltage to the 30100555 -98 9447 30100555 - 987 30100555
i need clear ans and solve very very fast in 20 min and thank you | plc ؛i need clear ans and solve very very fast in 20 min and thank you | plc ؛i need clear ans and solve very very fast in 20 min and thank you | ؛i need clear ans and solve very very fast in 20 min and thank you | ؛i need clear ans and solve very very fast in 20 min and thank you | i need clear ans and solve very very fast in 20 min and thank you | ᴅi need clear ans and solve very very fast in 20 min and thank you |