Q1 (a) Based on electrical DC circuit as depicted in Figure Ql(a), (1) Determine the mesh currents I, I, Is and I4 by using mesh analysis. Then calculate the branch current, Ia. (ii) Calculate the power at 50 V voltage source and determine whether the power is supplied or absorbed by the voltage source. Hi W 20V 50 50V 10V 4A 50 Ω 20 Ω 50 Figure Q1(a)

Q1 (a) Based on electrical DC circuit as depicted in Figure Ql(a), (1) Determine the mesh currents I, I, Is and I4 by using mesh analysis. Then calculate the branch current, Ia. (ii) Calculate the power at 50 V voltage source and determine whether the power is supplied or absorbed by the voltage source. Hi W 20V 50 50V 10V 4A 50 Ω 20 Ω 50 Figure Q1(a)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Subject name: Electrical Power Distribution.
For the circuit shown in the figure below, find the following. the current in each resistor,I2Ω(top) =,I2Ω(middle) =,I6Ω =,the power supplied by each source of emf P 4V(top) =,the power delivered to each resistorP 1Ω =,P6 Ω =,P2Ω(middle)=
QUESTION 7 An 120 V AC circuit has 100 Q of resistance, 75 Q of inductive reactance (X ), and 25 Q of capacitive reactance (XC). Answer the following: A. The total impedance (Z) of this circuit is ohms. (Round your answer to one decimal place.) B. The total current flow in this circuit is -26.6 amps. (Round your answer to one decimal place.) C. The power factor in this circuit is 0.89 . (Round your answer to two decimal places.) degree lagging (leading or lagging) phase angle. (Round degrees to one decimal pla D. This circuit has a 26.6 Click Save and Submit to save and submit. Click Save All Answers to save all answers. Type here to search Pr F7 F6 DII F3 F5 F4 F2 &
Rレ www 2V Figure 2 %3D 6. Determine the current at the load IAB in the given circuit in figure 2. RL = 10 ohms.
6
Calculate the required R1 in ohms RC=1920 ohms, IB=23 uA, VC=9V, R2=6916 ohms, RE=282 ohms and B=133.
Could you slove this dc electrical circuit
Question 4
(a) In figure (a) below, P₁ = 36 W. Is element 2 absorbing or supplying power, and how much? -48 W. Is element 1 absorbing or supplying power, and how much? (b) In figure (b) below, P2 Ⓡ 12 V 2 6V (b) 16+ +21 6 V 2 24 V
Si cantilever metal layer polySi heater Figure 2: Top view of the thermal bimorph cantilever structure showing the cantilever, metal layer, and poly§i heater layers in no particular order
In your solution, follow the sequence: Given, unknown, solution, and final answer. BOX your final answers. thank you! 2. A series-parallel ac circuit has two branches across the 60 Hz , 220 V power line. One branch has a 20 ohm R1 in series with a 10 ohm R2. The other branch has a 30 Mega ohm R3 in series with a 10 Mega ohm R4. Calculate the voltage across R4
Q10. To produce a voltage output to 9-Volt of the DC power supply circuit shown in Figure 3, what should be value of R2 if R1 is 1000. 1N4001 1A Fuse Bridge Rec. 240V AC In Out LM317 +V out Transformer Adjust R1 2000uf 0.1uF 1uF R2 OV ww wv