Q1\ A ball made of INOX AISI 365 steel with density of 8.52 gr/cm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m³.

Q1\ A ball made of INOX AISI 365 steel with density of 8.52 gr/cm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m³.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An oil of viscosity 0.1 Ns/m2 and relative density 0.9 is flowing through a circular pipe of diameter 50 mm and of length 300 m. The rate of flow of oil through the pipe is 3.5 litres/sec. The pressure drop in a length of 300 m will be N/cm?.
The data set of the diameters of the metal cylinders manufactured an automatic machine has sample size of n=28, mean of x= 49.94 mm and std. of S = 0.15 mm. Expected diameter of metal cylinder is µ = 50.00 mm. Can we be 95% confident that machine calibrated properly? Solution: v=n-1=27 ; ta/2=? P[X for 2 S VR μ+ (a Sl Vi -1-a =0.95
If you inflate your car tires at a garage near Lake Arrowhead (elevation: 5107 ft) and the average pressure reading was 40.0 psi, what would be the average pressure reading when you arrive at Cal Poly Pomona (elevation: 732 ft) two hours later? Assume that the atmospheric pressure linearly decreases as elevation increases at -1.0 psi per 1000 ft. O 41.0 psi O 44.4 psi O 35.6 psi O 39.0 psi
Situation 3: A calibrated test of a 0.00785 m² circular sharp-edge orifice in a vertical side of a large tank showed a discharge of 22,300 N of water in 1 minute and 40 seconds at a constant head of 1.20 m. Measurement of the jet showed that it traveled 1.92 m horizontally while dropping 0.8 m. 6. Determine the coefficient of discharge. a) 0.621 b) 0.597 c) 0.649 d) 0.721 7. Determine the coefficient of velocity. a) 0.84 b) 0.93 c) 0.74 d) 0.98 8. Determine the coefficient of contraction. a) 0.77 b) 0.97 c) 0.61 d) 0.67 B
Strarting from the velocity distribution in pipes given below R Vmax V V₂ 5.7510910 obtain the relationship for the ratio of maximum velocity to average velocity in terms of Darcy-Weisbach frictioin facror and show that this ratio increases with the friction factor,
Question on water resources engineering FLUID MECHANICS
B4
ANSWER KEY : 2.51x10^-3 in.
Soil mechanics
For a falling head permeability test, the following are given: Length of specimen = 375 mm Hydraulic conductivity = 1.72 m/min. Area of specimen = 1875 mm2 What should be the area of the standpipe for the head drop from 625 mm to 300 mm in 480 seconds? Select the correct response: 88.63 mm2 56.24 mm2 93.74 mm2 53.18 mm2
Re.?
I need the answer quickly