H.W no. 2Q1) 28 N.m torque is needed to turn the bolt around its axis as shown inthe Figure (1) below. Find the force F and the forces between thewrench's smooth face jaws and the hexagonal bolt head's corners Aand B. Suppose the wrench fits on the bolt simply such thatconnection is only formed at corners A and B.150 mm不14 mmFigure (1)Q2) Three cables are joined at the junction ring C. Determine the tensionin cables AC and BC caused by the weight of the 30-kg cylinder.A4515°30 kg30BFigure (2)Q3) A beam is loaded and supported as shown in Figure (3). The beamhas a uniform cross section and a mass of 20 kg. Determine thereaction at support A and the tension T in the cable.

Answered: Image /qna-images/answer/e74fbd8b-c5bc-418e-b95d-cce2e5207e49.jpg

Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm Figure (1) Q2) Three cables are joined at the junction ring C. Determine the tension in cables AC and BC caused by the weight of the 30-kg cylinder. 45 15 30 kg 30

Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm Figure (1) Q2) Three cables are joined at the junction ring C. Determine the tension in cables AC and BC caused by the weight of the 30-kg cylinder. 45 15 30 kg 30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces FB at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 mm 10 mm
The frame shown in Figure below consists of two members (BC and ABD) and it is subjected by the given point loads. Find all pin forces that act on this frame. 100 N 120 N -300 mm 500 mm 300 mm B D 300 mm A 100 mm 600 mm
Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 48-in. boom is held by a ball-and-socket joint at C and by two cables BF and DAE; cable DAE passes around a frictionless pulley at A. 48 in. W B y 20 in. The tension in cable DAE is The tension in cable BF is The reaction at C is - E lb. 16 in lb. lb) i + F For W = 340 lb, determine the tension in each cable and the reaction at C. 30 in. 20 in. lb) k.
The figure shows a bicycle wheel resting against a small step whose height is h = 0.100 m. The weight and radius of the wheel are W = 20.0 N and r = 0.390 m. A horizontal force is applied to the axle of the wheel. As the magnitude of increases, there comes a time when the wheel just begins to rise up and loses contact with the ground. What is the magnitude of the force when this happens? Number Units ✪ F
2.22 Calculate the centre distances for a v-belt drive given pulley pitch diameters of 180 mm (motor) and 400 mm (driven) when the belt is (a) an SPÁ 2 360; and (b) an SPB 3 800. [716 mm; 1 441 mm] Calculate the angle of contact on the smaller pulley for both cases. Determine the tension ratio if the groove ang- les are 38° and u is 0,25. (162°; 171
The lifting arm shown below needs to lift a weight of 4 (N). Assuming the links are weightless, determine the magnitude of the force being applied by the pin at B on the lifting arm to the nearest hundredth of a newton. 10Em) 6icm- 150 A Servo Horn Arm 4 (W) 'Servo
The frame in (Figure 1) supports the 350lb load. The pulley at C has a radius of 0.5 ft. The pulley at D has a radius of 0.25 ft. a) Determine the reaction at pin A. b) Determine the reaction at pin B.
The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces Fg at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 10 ww ww
Part B: The Steel beam in Figure b is supported by a ball and socket at D and supported by separate cables at B. If the tension in cable BA and BC is 7500N and 4500N, respectively, determine: a) The components of the i, j, and k components of the resultant force at point B using unit vector notation. b) Assume the mass of the beam is concentrated mid-span, calculate the mass of the beam. 1500 mm A 10000 mm 3000 mm 550 mm B 1650 mm NE
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
RAY F Enter Fpc: Enter Fr The figure above is a pin-joint frame with horizontal member length 1 = 2m and vertical member length h = 4m. (Note that the diagram is not to scale.) You are given that F₁ =45kN, RAY = 15kN and Rpy = 30kN. Use the method of sections to calculate the forces in members BC, FC and FE. Enter your answers in kilonewtons (kN) correct to 2 decimal places. Enter Fac: KN KN F₁ KN RDY