Q.6/ For the system shown in Figure 4, a step torque is applied at 0,(t). Find a. The transfer function, G(s) = 02(s)/T(s). b. The percent overshoot, settling time, and peak time for 02(t). [Section: 4.6] T(1) 0,(1) 02(1) ff 1.07 kg-m? HE 1.53 N-m-s/rad 1.92 N-m/rad

Q: I need to convert the drawing from a handwritten drawing to a typeface on a computer or computer in…

A: We need to convert the given handwritten drawing to a typeface.

Q: It's so hard to read, I need a handwrite version

A: We are not allowed to provide handwritten solutions. Hence, providing you typed solution shown…

Q: Determine the current into point A when R8 is 1 ΚΩ, 5 ΚΩ, 10 ΚΩ. R3 10 K R2 6.8 K R1 9.1 K El 48 V…

A: Thevenin's theorem states that any linear electrical network can be replaced by an equivalent…

Q: Face shields are made up of plastics. Select one: O True O False

A: 1) A face shield is an equipment that is used to protect the face from various contaminants. 2)…

Q: (0) L, = ? 18 mH L 47 mH L5 22 mH LT 10 mH L4 30 mH ll ll ll

A: Simple problem on netwrok.

Q: When the MPU takes an interrupt it runs a program called an INT INTR ISR IRQ SUV

A: When the microprocessor takes an interrupt, it halts the programs run for the various peripheral…

Q: Choose the correct instruction that will read data in from an I/0 device. IN AL, 60 IN 60, AL OUT…

A: In an I/O device the command "IN" represents the input command Here IN AL,60 means that move a…

Q: 1- Find is the written formula correct? If it's wrong,write the correct formula. MOV BL,DX MOV AX,BX…

A: As per bartleby guidelines I could solve only one question at a time for remaining questions you…

Q: determine the fifth roots of -32 . Leave answers in polar form

A: Let x be the fifth root of -32 So    x = (-32)1÷5

Q: Determine the Fourier series representation for the signal x (t) shown in Fig. P. 4.2.9.

A:

Q: The conducting rod of length I in the figure moves B. out without friction with velocity v. The…

A:

Q: Q3/TO design Carry Look ahead adder that add two (9-bit) numbersmust using * O 9 X-OR O 12 X-OR О 15…

A:

Q: When no key is pressed the input port (Port B) will read

A: in the given circuit the matrix connected two ports are given in which port A output is applied to…

Q: Choose the right answer ---When 4 minterms are combined in a K-map O a. 2 Literals are eliminated O…

A: According to the question we have to discuss the K-map. when 4 minterms are combined.....

Q: Difference between $monitor and $display. Explain the application of the verilog key words begin-end…

A: VHDL is Hardware Description language . It has different layer of abstraction. Reg is driven by…

Q: 2. Find 1₁, 12 and 13. 1522 30V +1 W 52 'IS W 12 30 12_2 W V81 13 3022 W 2012 2012

A: The given problem is from circuits.  The detailed solution is given in the next step

Q: If output port A = 1011 B and the "6" key is pressed, port B will read Port A (output) 0. 21 31 DO 4…

A: If input port A=1011 B  , and the "6" key is pressed then port B will read : options are: 1111 B…

Q: these errors occur from unknown sources O Arithmetic errors O Random errors O Systematic erorrs

A:

Q: Question 9 nag   Create an adder/subtractor circuit capable of the above arithmetic. Perform the…

A:

Q: -6 -5 For each number set, complete the following operations and predict what your output sums and…

A: Addition of two numbers in binary and check the condition of overflow occurance.

Q: Reactances are connected in series: |Xc11 = 100, IXC2| = 40, IXL1 = 30, XL21 = 70. What is the net…

A:

Q: Find Vo? 202 +12 V ww Vx=20V Vo 40 2V Select one: O a. - 12 V O b. 85.55 V O C. None of them O d. 12…

A:

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: We need to select correct option for given instructions .

Q: !They asked me to .. overtime do Make

A: They asked me to........................................overtime. Make is used whenever there is a…

Q: Bi

A:

Q: QUESTION 9 If port A = 0111B and the "1" key is pressed, port B will read Port A (output) 3. DO D1 A…

A: Here, port A is connected to 0111B and switch 1 will pressed

Q: (a) Estimate the transconductance for the transis- tor in Fig. P4.18 for VGs=4 V and VDs = 4 V. (b)…

A: The transconductance is the ratio of the change in drain current to the change in Gate-source…

Q: Choose the correct instruction that will send data to an 1/0 device. IN AL, 60 O IN 60, AL OUT 60,…

A: MOV instruction : Copies the data item referred to by its second operand (i.e. register contents,…

Q: It's hard to read, I need a clearly handwrite version

A:

Q: Choose the correct instruction that will send data to an l/0 device IN AL, 60 IN 60, AL OUT 60, AL…

A:

Q: _@311 what is the gate for Crvenit *. when input" 1" = 6v input "O" - OV REDMI NOTE 8 PRO AI QUAD…

A: This is a problem of analysis of diode. The calculation is shown in the next step

Q: 5. R=90.5 MQ + 2.2 KQ is converted to :* O 90.502 MQ 905.022 MQ 90.502 KQ O No one above

A: R= 90.5M + 2.2 K  R= 90.502 M ohm

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.