Q.36: For the current locus diagram shown beside: Draw the equivalent electric circuit diagram corresponding to the given locus? then find the value of each element in the 20A 300 10020°v circuit if @=377rad/sec? Also find the total current at resonance? (Ans.: Zc=4.33-J2.52, R=52, RL=52 & I10=47.32A)

Q.36: For the current locus diagram shown beside: Draw the equivalent electric circuit diagram corresponding to the given locus? then find the value of each element in the 20A 300 10020°v circuit if @=377rad/sec? Also find the total current at resonance? (Ans.: Zc=4.33-J2.52, R=52, RL=52 & I10=47.32A)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

At resonance Select one: a. magnitude of capacitive reactance > magnitude of inductive reactance. b. magnitude of capacitive reactance = magnitude of inductive reactance. c. magnitude of capacitive reactance < magnitude of inductive reactance. d. none of above.
A sinusoidal haseband signal with a frequency of 5kHz is transmitted using DSB-LC. The received signal is R = 10[1 +0.2 cos(2m5000r)] cos(2r10°r) Volts. The shown system is used as a receiver. The BPF is ideal and its center frequency is 1.002MHz and bandwidth 7kHz. The demodulator has input-output characteristics (V, = 4V/). The LPF is ideal with an adjustable cutoff frequency. Determine the output signal waveform of this system. You need to specify the cutoff frequency of the LPF to obtain the original message back at Y. R BPF Demodulator B (B-4A) LPF DC removal
4.) Given the following LRC circuit (L = .012 H, R = 8 ohm, C = 2 F, w = 2*60*pi), Vmax = 100V. A.) Draw a phasor diagram of the circuit. B.) By what degree does the voltage source lead or lag the current? C.) What frequency of the voltage source is necessary to reach resonance?
Find DFT values of x-[2 1 9 2] and plot amplitude and phase spectrum. Write axis labels.
(7 (6) Find the low frequency response by determining poles due to each coupling and hypass capacitor (CE, Cin & Cont). Ignore to for the BJT. 2/5 + Ps M Cin Vcr R₂ Vcc T R₂ Cont " ERL Vout
Please solve Quickly
In the filter shown in figure 8 the ratio between the output AC voltage Vout and input voltage Vin is given by Vout R wCR (1) R+ j(wL – 1/(wC)) Vin R+ j(w?LC – 1) - -
mosfet low frequency question
Find DFT values of x= [4 4 8 4] and plot amplitude and phase spectrum. Write axis labels.
() (2n) uch2). Sketch a discaete time signal xcn) = 27 for 12. -2 2n L2. Obtain- (i) y,cn) = 2 xin) + SCn) 3/7 xn). uC 2-n)
R1 a VSm ISm ZVSph LI ZISph In the circuit, the voltage source amplitude and phase are 40 V and 0.75 rad correspondingly; the current source amplitude and phase are 20 mA and 0.75 rad correspondingly; The signal frequency of both sources is 26 MHz; R1=8 kohm, L1= 45 uH (u=micro), C1= 1.4 pF. Using any appropriate techniques, find the following parameters of Thevenin equivalent circuit with respect to the terminals "a" and "b". Present the Thevenin source in the polar form and the Thevenin impedance in the algebraic form.
Q6: A frequency modulated voltage wave is given by the cquation: e = 12 sin (6 x 10t + 5 cos 1250 t) Ve 2Tfm Find (i) carrier frequency (ii) signal, frequency (ii) modulation index (iv) maximum fm mf frequency deviation (v) power dissipated by the FM wave in 10-ohm resistor, Df