For the network of figure below, if the mid-band voltage gain is (-2.47), answer the following:a. Draw the ac equivalant circulit.b. Calculate Ci and Co.d. Determine f and fee. determine the cutoff frequency1. Sketch the frequency response for the high-frequency region using a Bode plot.12 VCw = 4 pFCw = 6 pFC= 8 pF!!C12 pF%3!Ca = 3 pF2.7 ka10 uFRasIpss= 10 mAVp-6 V0.6 k210µFZ, R247 kNI M20.51 ks2 = 20 uF

Answered: Image /qna-images/answer/7d68721b-fb58-474c-9572-355da19f1d4a.jpg

thể hetwork of figure below, if the mid-band voltage gain is (-2.47), answer the following a. Draw the ac equivalant circuit. b Calculate Ci and Co. d. Determine fs and f e. determine the cutoff frequency f. Sketch the frequency response for the high-frequency region using a Bode plot 12V = 4 pF C 8 pF Cw Cw = 6 pF C 12 pF %3D Ca= 3 pF 2.7 kQ 10HF Ra Inss 10 mA Vp --6 V 0.6 k2 10pF 7 RL 4.7 k2 1 M2 0.51 k2 20 uF

thể hetwork of figure below, if the mid-band voltage gain is (-2.47), answer the following a. Draw the ac equivalant circuit. b Calculate Ci and Co. d. Determine fs and f e. determine the cutoff frequency f. Sketch the frequency response for the high-frequency region using a Bode plot 12V = 4 pF C 8 pF Cw Cw = 6 pF C 12 pF %3D Ca= 3 pF 2.7 kQ 10HF Ra Inss 10 mA Vp --6 V 0.6 k2 10pF 7 RL 4.7 k2 1 M2 0.51 k2 20 uF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

answer with handwriting
P3 For the series RLC circuit given in Figure 4 for Vs=10sinot R=2.2 2, L=100 uH and C=1000 uF a) Obtain the resonant frequency and the half-power frequencies. b) Calculate the quality factor and bandwidth. c) Determine the amplitude of the current at 60, 6 and 02. d) Plot the current amplitude versus frequency e) Use LTSPICE to plot frequency response.
Determine the transfer function that produced the following Bode plot. (Note: the values here were chosen so that this transfer function could be determined exactly): 120 Bode Diagram 100 80 60 40 20 45 -90 -135 -180 100 10 102 10 Frequency (radis) 10 (ge) pronbep (Bop) oe
Answer letter B only
Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of 2log10[H(jw)] and the phase angle graph of H(jw) Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
35
What is resonance? Explain how the condition of resonance is obtained in a series RLC circuit. Determine impedance, current, and power factor of RLC circuit at resonance.
b. Choose the suitable choice foL ping of the following sentences 18 Maces 1. In order to tune a parallel resonant circuit to a lewer frequency the capacitor must a. Be increase. b. Be decrease. . BeZero. Remain the same 2. Ina very low frequency a series resonance behaves as Imost purely .......... circuit a Resistive. b Capacitive. . Inductive. d. Inductive and capacitive 3. Real part of the total impedance at resonance for complicated AC circuit is a. Positive Value. b. Zero Value. Negative Value. d. Complex value 4. For admittance locus the maximum obtained power factor is depend on a Maximum current b. Maximum voltage . Minimum power d. Minimum angle 5 Any non sinusoidal symmetrical waves are basically composite from fundamental wave plas .. of harmonics waves. aodd b. even . odd even d odd of even 6. If we append an inductance in series to an RL series circuit the time constant will be a Increases b. Decreases. Increases and Decreases. Increases or Decreases 7. The double energy…
i need the answer quickly
Q2 Sketch the asymptotes of the Bode plot magnitude and phase for the controlled transfer function of the system described in the figure, calculate the gain and phase: margins, Take K = 1. d42u42 S+
All of the following statements are correct except: : Resonance frequency happens when the frequency is changing. The bandwidth is defined as the ratio between W0 and Q The selectivity in resonance frequency is an important factor in determining Xl. The voltage across the L and C elements is zero but maximum in R
In Matlab for the transfer function