Q.3) The motor attached to the left-end of a steel (G= 11x10³ ksi) shaft AB delivers 60 hp which rotates the shaft AB at 18 Hz. The gears at C and D fixed to the staft AB transmit 40 hp and 20 hp to attached machinery, respectively. The shaft AB is supported on smooth bearings at A and B, which allow free rotation of the shaft. If the allowable shear stress in shaft AB is 10 ksi and the allowable angle of twist of D with respect A is 0.3 degree, determine the diameter of the shaft. 12 inch 10 inch 8 inch

Q.3) The motor attached to the left-end of a steel (G= 11x10³ ksi) shaft AB delivers 60 hp which rotates the shaft AB at 18 Hz. The gears at C and D fixed to the staft AB transmit 40 hp and 20 hp to attached machinery, respectively. The shaft AB is supported on smooth bearings at A and B, which allow free rotation of the shaft. If the allowable shear stress in shaft AB is 10 ksi and the allowable angle of twist of D with respect A is 0.3 degree, determine the diameter of the shaft. 12 inch 10 inch 8 inch

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel shaft with a constant diameter of 60 mm is loaded by torque applied to gears attached to it as shown in the figure. Using G=83 GPa, determine the relative angle of twist of gear D relative to gear A.The steel shaft shown in figure rotates at 6 Hz with 55 kW taken of at A, 40kW removed at B and 95 kW applied at C. Using G =83 GPa, determine the maximum shearing stress and the rotation of gear A relative to gear C.
Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an allowable shear stress of 7.4 ksi, or having a relative angle of twist beyond an allowable value of 0.35 degrees per 1-ft length. The ratio k-d,/d,=0.75
A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50 kW and 25 kW, respectively. Compute the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G=75 GPa.
A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and firmly attached. The diameter d1 = 70 mm and the diameter d2 = 90 mm. Brass G = 39GPa and steel G = 77.20 GPa. Determine: The torque that can be applied if the deformation at one end is 10 degrees. Answer: T = 8.64 kN – m The torque that can be applied if the maximum shear stress in brass is 70MPa and in steel is 110MPa. Answer: T = 6.352 kN – m Recommendation: analyze by segments. The first segment is only brass, then the composite part between brass and steel, and the last part only steel. In the composite segment, use only one material. In this same segment, equalize the deformations.
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and freely in bearings at points A and E. The shaft is driven by a gear at C, which applies a torque T₂ = 625 N_m in the direction shown in the figure. Gears at B and D are driven by the shaft and have resisting torques T₁ and T3, acting in the opposite direction to the torque T2. We know T₁ = 400 N.m, but T3 is not explicitly given in the problem. Segments BC and CD have lengths LBC= 550 mm and LCD = 400 mm, respectively, and the shear modulus G = 80 GPa. Determine the maximum shear stress in each segment of the shaft and the angle of twist between gears B and D. pôrôć -LBC LCD T3 E
A torque of Tp- 1335 N-mis applied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely. Assume shafts (1) and (2) are salid 20-mm-diameter steel shafts. Determine the magnitude of the maximum shear stress acting in shaft (2). 230-mm dia. 150-mm dia. O 988.1 MPa O 898.6 MPa O 1148.0 MPa O 1098.5 MPa O 849.9 MPa
A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc i B (2) b Tc (3) Tp lb-ft D
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
Calculate angle of twist of B with respect of A in rad
Draw the intemal torque diagram .
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa