Q.3) The figure shows a hollow cylindrical shaft of outer diameter do 50 mm and inner diameter d; = 40 mm is subjected to a torque T 250 N.m and to an axial loadP. Assume the maximum tensile stress allowed is 40 MPa. Determine the principal stresses, the maximum shear stress and the maximum axial de load P that can be applied without exceeding this Gallow allowable tensile stress.

Q.3) The figure shows a hollow cylindrical shaft of outer diameter do 50 mm and inner diameter d; = 40 mm is subjected to a torque T 250 N.m and to an axial loadP. Assume the maximum tensile stress allowed is 40 MPa. Determine the principal stresses, the maximum shear stress and the maximum axial de load P that can be applied without exceeding this Gallow allowable tensile stress.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa. G=70 GA (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameter d if it is operated at 3000 rpm? (c) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor Motor
A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius r2 equal to 1.5 times the inner radius r1 (a)If the maximum shear strain in the tube is measured as 400x10 to the power 6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist is 0.125 degrees per meter and the maximum shear strain is to be kept at 100x10 to the power 6 rad by adjusting the torque T, what is the minimum required outee radius (r2) min ?
Find p1 and p2
MN=45
4-Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 50 mm x 31 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 22 kN (tensile), 30 kN (compressive), 22 kN (compressive) respectively. Take E as 100 GPa, Poisson’s ratio as 0.3 The stress along length direction (Unit in MN/m2)= _____________ The compressive stress along width direction (Unit in MN/m2)= _____________ The compressive stress along depth direction (Unit in MN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
Additional problem: A solid rod with a radius of 10 mm is subjected to a combined loading with two forces and one torque, as shown in the figure below (T-5 Nm). Compute the normal stress o, and shear stress at point H and K. C K H 300 mm SAN-m Z 700 N 250 N X
1. Determine stress distributions of a rotating ring (See the figure below; Angular speed: 0; Mass density: p). a b
Q24 Find the stresses in each direction, also find the change in volume of the block of dimension 115 mm x 50 mm x 37 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 22 kN (tensile), 20 kN (compressive), 19 kN (compressive) respectively. Take E as 180 GPa, Poisson's ratio as 0.3
None
F3.A shaft is composed of two 6-in. diameter sections coupled together (see figure below). Part AB is bronze and part BC is steel. A torque is applied at the free end which causes a maximum shear stress in the bronze shaft of 10,000 psi. Find the angle of twist of the free end. Assume the modulus of rigidity of bronze is 6 (106) psi and that of steel is 12(106) psi. Bronze Dia. = 6 in. A 3' Steel B Match each item to a choice: Angle of twist T
Solid cylindrical shaft with bending moment M = 440 Nm, torque T = 40 Nm and shear as shown in the figure V = 700 N is exposed to the force. Analytically analyze the principal stresses and their directions at point A. obtain with formulas and also with Mohr's circle
4. For an element subjected to stresses of x= 70 ksi y=-15 ksi xy=30 ksi SAH: (a) Draw Mohr's circle (b) Calculate the value of the principal stresses