Q.3 A three-phase, four-pole, Y-connected, 480 V induction motor is driving a 400 Nm constant-torque load. The motor has the following parameters: N₁ N₂ =1, Protational = 1 kW The motor is driven by a slip energy-recovery system. The triggering angle of the dc/ac converter is adjusted to 1200. Calculate the following: Motor speed Current in the dc link Average voltage at the input of the dc/ac converter Rotor rms current Stator rms current Power returned back to the source

Q.3 A three-phase, four-pole, Y-connected, 480 V induction motor is driving a 400 Nm constant-torque load. The motor has the following parameters: N₁ N₂ =1, Protational = 1 kW The motor is driven by a slip energy-recovery system. The triggering angle of the dc/ac converter is adjusted to 1200. Calculate the following: Motor speed Current in the dc link Average voltage at the input of the dc/ac converter Rotor rms current Stator rms current Power returned back to the source

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.6 The starting current of a 3-o induction motor is 5 times the rated current, while the rated slip is 4%. The ratio of starting torque to full-load torque is (b) 0.8 (d) 1.2 (a) 0.6 (c) 1.0
Problem (3) In the circuit shown, i(t) = 10 sin 1.5t . Calculate the value of L such that v(t) = Vo sin 1.5t V. Find %3D Vo. 1Ω + i(1) (t) 1 F
Q5:- Adjust a fire angle for a three-phase fullwave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If this DC machine is operating as a motor with rated flux at rated speed, calculate the rated torque (TR), rated current (IR), rated voltage (VR), efficiency (n) at the rated point, taking into account the winding losses. Find the speed (@NL) of this motor in no-load condition. TR Nm IR А VR V Eff = % ONL= rpm
g) What is an advantage if the starting Torque of the induction motor is higher than the nominal load Torque? h) What are the main differences when the equivalent circuits of transformer and asynchronous motor are examined?
A 0,9 kW DC shunt motor is loaded by a constant torque of 12 Nm. The armature resistance of the motor is 5 Ω, and the field constant KØ = 3 Vs/rad. The motor is driven by a half wave thyristor converter. The power source is a 140 V, 50 Hz. The triggering angle of the converter is 450 and the conduction period is 1650 . Calculate the motor speed and the developed power.
Which of the following statement is correct for the causes of low power factor? O The power factor of induction motor falls with the decrease of load. O Most of the induction motors operate at leading power factor. O Arc lamps operate at high power factor. O The induction furnaces operate on high power factor.
6. The efficiency of DC to DC converter to drive de motor is --- than AC to DC Drives a) lower b) equal e) higher 7- The Four-quadrant operation of de motor can he implanted using -- e) Semiconverter 8. The supply froqueney of induction motor using frequency control is changed to - a) Full converter b) Dual converter a) abuve rated frequency. b) below rated frequency. e) Abuve and below rated frequency. 9. The stable operation in torque- speed churacteristic for induction motor occur: e) at slip 05 to Sms 10. The regenerative hraking for de to de convernter fed de motor would be effective if the a) between maximum slip and s0 h)at slip =1 operating speed m : a) or t b) > uin c) thi
An 8-pole, 50 Hz, 3-phase induction motor has a full-load slip 2.5% and maximum torque of twice the full-load torque. At what value of slip does the maximum torque occur? Ans[0.093]
Q5:- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.