Q5:- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.

Q5:- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

"A 220 V, compensated shunt motor driving a 1084.8 N.m torque load is running at 1000rpm. The efficiency of the motor at this load is 92 percent. The combined armature, compensating winding and interpole resistance is 0.01 ohm, and the resistance of the shunt field is 65 ohm. Determine the following parameters of the motor: (i) Input power (in kW) (ii) Field current (in Amp) (iii) Armature current (in Amp) (iv) Induced voltage in armature (in volts) (v) Torque developed by motor (in N.m) and (vi) The resistance of a dynamic breaking resistor (in ohm) that will be capable of developing 678 N.m of braking torque at a speed of 750 rpm. Assume windage and friction at 750 rpm is the same as at 1000 rpm. [Hint: 1 lb-ft = 1.356 N.m]" T T T Arial v 3 (12pt) - T-
600V, DC series motor operates at 600 rpm and rated load. Armature resistance 0.1 ohm and series fieldwinding resistance is 0.05 ohms. At full load, the motor draws 195 A current. A) Find the reverse(back) EMF value at full load. B) Find the power and internal moment produced in the armature under full load.
what is the best switch for buck boost converter and why
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If the motor speed is reduced to 50% of the rated speed (1200rpm), find the inductive voltage, the induced current, the motor efficiency and the motor speed at no load to obtain the rated torque at this speed. (Field supply current will be considered constant). I A V V Eff % ONL rpm
A Flyback converter (for questions 1-3) shown below has the following parameters. Vin-100V, Vo-20v, Po-40W, D-0.25, Fsw-250kHz 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. NI: N2 - 5: 3 B. NI: N2 - 3:5 C. NI: N2- 5:2 D. None of the above
A 20hp, 240V, two-pole and 60-Hz, Y-connected wound- rotor induction motor. Its equivalent circuit components are Rj=0.260, R2=0.180, Xj=0.470, X2=0.480, Xm=15.60, Pmech=550W, Pcore=480W, and Pmisc=120W. For a slip of :0.045, find a) The stator copper losses PSCL and the air-gap power PAG b) The power converted from electrical to mechanical form Pconv c) The induced torque tind and the load torque tjoad d) The overall machine efficiency e) The motor speed
w5
Q1 (a) Sketch the torque-speed profile of DC motor, induction motor, and synchronous motor. (b) Briefly describe the main components of load torque in electrical drives.
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
I need the answer as soon as possible
Derive the power equation for DC motor. Give the different load-torgue curves for each, DC. motors
Q5:- Adjust a fire angle for a three-phase fullwave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.