Q.3 (a) A 30 cm x 15 cm venturimeter is provided in a vertical pipe line carrying oil ofspecific gravity 0.9, the flow being upwards. The difference in elevation of the throatsection and entrance section of the venturimeter is 30 cm. The differential U-tubemercury manometer shows a gauge deflection of 25 cm. Calculate:(i) the discharge of oil, and(ii) the pressure difference between the entrance section and the throat section. Takethe co-efficient of discharge as 0.98 and specific gravity of mercury as 13.6.

Answered: Image /qna-images/answer/70ec20a3-1b0c-4fb7-86db-c34eab351b29.jpg

Q.3 (a) A 30 cm x 15 cm venturimeter is provided specific gravity 0.9, the flow being upwards. T section and entrance section of the venturim mercury manometer shows a gauge deflectio (i) the discharge of oil, and (ii) the pressure difference between the entra the co-efficient of discharge as 0.98 and s

Q.3 (a) A 30 cm x 15 cm venturimeter is provided specific gravity 0.9, the flow being upwards. T section and entrance section of the venturim mercury manometer shows a gauge deflectio (i) the discharge of oil, and (ii) the pressure difference between the entra the co-efficient of discharge as 0.98 and s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

advantages and disadvantages of pressure compensated valve
1. The manometers are suitable for comparatively C. very high A. low B. high pressures. D. none of the above
22-5MN/m EI 40KN /M 3m 6m E= 200GPO I= 300 X106 mmy Determinc vesticel deflection at joiat B
Subject: Hydraulics
200mmø 690mm 300 mm 400 mmø 金Ho0 Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm.
An oil of specific gravity 0.89 is flowing through a horizontal venturimeter fitted to a 242 mm diameter pipe at the rate of 108 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 841 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.13 N/mm2.
Ql:-A cylinder of 1lft diameter and 2ft length floats in a tank that contains a liquid of specific weight .A u-tube manometer is connected as shown in figure. What is the weight of the cylinder whose upper the surface is flush with fluid surface PA--0.1 psi Water 2 ft Cylirder Gage fluid SG- 1.5 Sp wt.y 0.5 ft 02. w1
a 150 mm by 50mm venturi meter is installed in an inclined pipe carrying oil. the venturi distance between the inlet and throat is 20cm. the flo is upward through the meter. a differential manometer containing mercury the (sp. gr=13.6) is attached to the inlet base and throat. compute the deflection of the mercury if the actual discharge of pipe is 0.55 m³/s. assume the venturi coefficient to be 0.97.
uservoir discharges into a 55-inch pipe that discharges freely, as shown below. What is the pressure in the pipe at point A? Consider friction. Use f =0.02 Elev 155 ft Inv. @ A 134.2 ft 55 in 140 ft Inv. 120 ft 420 ft 900 ft 1450 ft a. 502 psf b. 502 psi c. 457 psf d. 457 psi e. 36 ft ,what is the velocity at point B? a. 17.5 fps b. 36 fps c. 3.6 fps d. 4.57 fps e. 50.2 fps ar
Calculate the pressure difference between points A and B for the differential manometer below.
Homework help
Hand written plzzzzz asap..i'll give you more votes if you solve 30-40 mins...