The ligure shoWs a tank discharging through a pipe with a nozzle at Its end. Find the discharge and the pressure at the base of the nozzle. Losses are: Tank to the base of nozzle is 5(V./2g and through the nozzle is 0.05(V)/2 (V Is the velocity in the pipe and Vi is the velocity at the tip of the nozzle) Water D I50mm Dy= 50mm

The ligure shoWs a tank discharging through a pipe with a nozzle at Its end. Find the discharge and the pressure at the base of the nozzle. Losses are: Tank to the base of nozzle is 5(V./2g and through the nozzle is 0.05(V)/2 (V Is the velocity in the pipe and Vi is the velocity at the tip of the nozzle) Water D I50mm Dy= 50mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

bai 8
Q1: A pressure of 10 kPa, gage, is applied to the surface of water in an enclosed tank as shown in figure. The temperature of the water is 20°C. Find the actual discharge of waterjet at the outlet through orifice of 0.5 cm diameter. 10 kPa gage 0.5 m Cd 0.61 Jet
M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
Question 6 In the schematic below, water flows through the pipe and enters a sudden contraction nozzle. To hold the nozzle in place, calculate the axial component of an anchoring force (FA) that would be necessary. Provide a sketch of your control volume. p = 1.940 slugs/fts, 1 ft = 12 inches, 1 lb-s? = 1 slug-ft Section (1) Uniform flow P-75[psi] V,-25[ft/s] Section (2) Uniform flow P2=0 [psi] V=100[ft/s] D;=3 [in] Flow in circular pipe Flow in circular pipe Sudden contraction nozzle
Tube diameter 145 mm(xx=45)
For the system in the figure, calculate the distancevertical between the surfaces of the two tanksWhen water at 10°C flows from point A to point B, arate of 0.03 m3/s. Elbows are standard. Thetotal length of 3 inch tube is 100meters. The length of the 6-inch pipe is 300 m. (T)
Question - Civil hydraulics The diameter of the U-tube is one-tenth the diameter of the enlarged ends, and a double column enlarged ends manometer is used to measure a minor pressure differential between two points of a system transporting air under pressure. Water is employed as the heavy liquid, and oil with a relative density of 0-82 is used as the lighter liquid in both limbs. Calculate the difference in pressure in millimetres of water for a manometer displacement of 50 mm, presuming the lighter liquid's surfaces stay in the larger ends. If carbon tetrachloride, which has a relative density of 1.6, were used in place of water but the pressure conditions remained the same, what would the manometer read?
For venturi-Meter shown in Figure, compute the velocity in the Pipe of (300mm) diameter, and the passing dis charge in (L/min) units. also Neglect all losses. DI=200mm Dz=300mm r.d=1·25 Yugho 118m
Question 3: 150 m long commercial steel pipe is to convey 30 L/s of oil (s=0.9, μ-0.038 N.s/m² from one tank to another (submerged discharge) where the difference in elevation of the free liquid surface is 2 m. The pipe entrance is flush and there is a fully open gate valve in the line. Using only basic scientific calculator, find the diameter theoretically required. Use k=0.19 for fully open pipe or follow the following table (Table 8.3). Flush Valve L, e, Q TABLE 8.3 Values of loss factors for pipe fittings Fitting k 10 Globe valve, wide open Angle valve, wide open Close-return bend 5 2.2 L/D 350 175 75 T Az
Please solve
Determine the flow in lps on the orifice between the 2 tanks shown below.
Three pipes of different lengths and diameters connected in series as shown discharges 169 lit/sec. If f=0.012 and disregarding minor losses, determine a. the head loss in each pipe. b. the diameter of an equivalent single pipe that could replace all the 3 pipes. ASAP