Q.28: For the circuit shown: V,-150cos500t Volt500 lurns1. Specify the numerical value of R for maximum212 20MITpower dissipated.2. Compute the maximum power dissipated in RL.RLV,1000turns(Ans.: RL=232 & Pmax=461.14W)Tideal

Answered: Image /qna-images/answer/110e7d50-bbb2-4f2c-acc7-229c0151d4d3.jpg

Answered: Q.28: For the circuit shown:…

Q.28: For the circuit shown: V,-150cos500t Volt 1. Specify the numerical value of RL for maximum power dissipated. 2. Compute the maximum power dissipated in RL. (Ans.: RL=232 & Pmax=461.14W)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1. a) Figure Q1 is a single phase 2-level voltage source converter (VSC) with a total DC voltage V-1000V. A PWM scheme, by comparing a reference value with a 1kHz triangular waveform, is used to control the switches S₁ and S2, and output 340v at Vo. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle and the modulation index. Va + 2 it Va d + TS₁ V {1+5₂ = Figure Q1 A single phase VSC
Q1: Draw the d.c load line for the circuit shown in figure. NO SIGNAL Van Vce= 12.5 V www Re=25 ka
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.49 V respectively. The form factor of this circuit is ___________________. a. 1.63 b. 3.27 c. 0.61 d. 1.17
a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R = 1092, L=20 mH, and a = 60°. Determine: i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. Vs S₁ S4 Figure $3 $₂ Lo Vo
A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.
8.What is the effect of increasing the value of the capacitance In single phase half wave with RL 9. Give an example of a practical case of half-wave uncontrolled rectifier with RL load connected in parallel with C. 10. Propose another circuit(s) to convert AC signal to DC signal.
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
Q2) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input voltage and used to supply resistive load of 10 2. Determine rsm voltage, rms current, ripple factor and dissipated power in the resistor R. If a = 45° and f = 50 Hz. %3D
i need the answer quickly
Design a POWER SUPPLY with 5V output voltage. Use zener diode as a voltage regulator. Then solve for theoretical computations. Thanks!
1) a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two ac outputs and calculate turns ratio of live transformer. voltage i) 10 V ii) 100 V 2) b) Consider a circuit using Si diodes and 10 k ohms resistors. Design this clipper circuit with output ranges below; i) -0.7 V and above ii) +2.1 V and above iii) +1.4 V c) As given in the figure a clamper circuit with the input +10V- signal Vi is proposed to design. Determine the output voltage with the exact solution step by step. Sketch transfer characteristic Vo versus V₁. V₂ Vo H 2RS -10V- -2√ 01 Vo Trims