Q.2) A plate is supported by a rope and two hinges as shown in figure. Assume that hinges do not exert couples on the plate, and the hinge at A does not exert a force on the plate in the direction of the hinge axis. If the plate is uniform with 50 kg mass, determine the tension in the 240 mm 240 m 400 min горе. 400 mm 200 mm! 200 mm 480 mm

Q: Three cables are used to tie the balloon shown in Figure. Determine the magnitude of the vertical…

A:

Q: A 415 kg safe is hanging from the apparatus below.  Determine the tension in the cable.  Dimension…

A:

Q: The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A: To find the internal forces in members AB, BD, BC, and CD of the truss, we can analyze the forces…

Q: The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal…

A: Find outDetermine the tension in the cable AE.Given(I kip = 1000 lb)Load P = 2 kips = 2000 lbMoment…

Q: in the truss below, the maximum force(s) will occur in members GF, AF, or AB. What component…

A: In the truss below, the maximum force(s) will occur in members GF, AF, or AB.What component sustains…

Q: A 550 N cylinder 1.4 m in diameter is lodged between two cross pieces which make an angle of 110°…

A:

Q: For the shown frame structure, the uniform beam AB weighs 480 lb and the uniform column CF weighs…

A:

Q: The system shown consists of three cables; 1, 2 and 3. Cable 1 passes through a frictionless pulley.…

A: Given Data m=6 kg y1 = 1.3 m y2 = 1.1 m y3 = 1.8 m x1 = 2.7 m

Q: Find: the force in the members MQ, OL, and LN and state whether they are in tension or compression.…

A: Cut the section as shown in the following figure and apply the method of sections to find the…

Q: The homogeneous 200-lb sign is suspended from three wires. Find the tension in each wire.

A: Weight is 200lb  sinθ=45  cosθ=35. ∑Fy=0 T1 is completely horizontal and Due to symmetry  T2=100 lb…

Q: #4 Handle AC can only rotate about the z-axis at point A. A 10 lb force is applied as shown at point…

A:

Q: The jaws and bolts of the wood clamp in Fig- are parallel. The bolts pass through swivel mounts so…

A: Consider the diagram shown below for the upper jaw.

Q: bearings C and D) as shown below. Determine the tension in cable AB and the support reactions at…

A:

Q: -?- W A 2.5 ст 5.0 ст —

A:

Q: A 7-ft boom is held by a ball and socket at A and by two cables EBFand DC; cable EBFpasses around a…

A: Given: The length of boom, L = 7 ft The force acting at C, P = 390 lb

Q: 4. The mobile shown in the figure below hangs at equilibrium. It consists of objects held by…

A: From linear equilibrium, Net upward force= Net Downward force From rotational equilibrium, Total…

Q: center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if…

A:

Q: A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at…

A:

Q: 8. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

A:

Q: A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a…

A: Given: The length of the beam is, l=2 m The mass os the beam is, W=10 kg×9.81 ms2=98.1 N The mass…

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

A:

Q: If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the…

A: Consider the support point O as origin. Thus, the cooridnates of points are, , , and .Write…

Q: The truss shown is used to support a 9 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A:

Q: A 12.0 kg weight hangs from a 7.50 m pole as illustrated in the diagram.  The pole has a mass of 8.0…

A: Write the given value using suitable variables. Here W signifies given weight, L signifies pole…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.