Q.19 What is the thickness (in mm) of an existing WBM overlay when the mean deflection observed was 1.75 mm, the standard deviation was 0.35 mm and the temperature at time of observation was 35°C? [Assume traffic at the end of 10 years is 3500 commercial vehicles per day] (a) 170 (b) 194 (c) 214 (d) 232

Q.19 What is the thickness (in mm) of an existing WBM overlay when the mean deflection observed was 1.75 mm, the standard deviation was 0.35 mm and the temperature at time of observation was 35°C? [Assume traffic at the end of 10 years is 3500 commercial vehicles per day] (a) 170 (b) 194 (c) 214 (d) 232

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plate having size 12 by 15 meter is pulled with velocity of .08 m/s over a fined plate at a distance of .3 mm with the viscosity of .03N-sec/m2 . Find the Force.
Help
GEOTECHNICAL ENGINEERING: The following measurements were made when a plastic limit test was done and the diameter of the crumbled threads were 1/8 in (3mm). Calculate the plasticity index of the soil. Mass (g) Empty can 65 Can + Moist Soil 92 Can + Dry Soil 88
Answer asap. will upvote
Describe about the flow nets and why are they used?
The long ranger is riding through a sandstorm. Does his mask (a bandanna that covers his nose) significantly decrease the amount of sand he breathes in? assume the bandanna is made of fibers, each 300 μ in diameter. They are woven in a simple weave that blocks 75 % of the projected area; the remaining 25 % is open, with holes up to 75 μ in diameter. For the purpose of this problem, the bandanna may be considered equal to a single row of parallel fibers, each 300 u in diameter, with 75 % of the flow area blocked and 25 % open. The gas velocity approaching the cloth as he breaths is 1 m/s. a). Estimate both the collection efficiency for 10 u particles and the cut diameter for bandanna used as a filter
Question 4.5 Reinforced concrete design
We find the zero force members by inspections؟ Select one: True False
8) Explain briefly why the regions in the below given graph have curved boundaries rather than straight border lines? Cataclastic Flow Plasticity 10-55-1 Power-Law Creep o/u -Coble 10-125-1 NH 0.1mm defomation mechanism map 9) If you are using a precipitation strengthening against creep, this mean what type of creep mechanism is dominant for that application? (Explain your assumption). 10) The Q value in the following equation is supposed to indicate the type creep (creep mechanism). Use the figure given in the Question 8 and what type of creep experiment would you carry out to determine the value of Q? s=AD"eQ/RT) 11) The value of Q can be confusing and different interpretations may arise. Explain very briefly why this is so?:
A stone is thrown with an initial velocity of 500 m/s upward at 30° to the horizontal. Neglect atmospheric resistance and any change in g, compute the radius of curvature, r of the path of the projectile 20 sec after it is thrown. Draw the necessary figure that will support your solution.
In an Oedometer test, what is the purpose of using a steel ring? none of the available options O provides drainage reduction side friction between the soil and steel prevents drainage prevents lateral deformation
Q7 Q7: A cement factory has two lines. Each line is operating separately. If the production properties (average and standard deviation of compressive strength) are as shown in table below: 1) determine the best line, 2) find the 95% confidence interval for the variance and standard deviation if the variance is two time than the variance given (assume n = 15 for both lines). Line No. Average MPa Standard deviation MPa Line I 15.2 3.3 Line II 14.2 1.2