Q.1) For the state of stress shown below, use stress transformation equations to determine the normal and shear stresses after the element has been rotated (a) 30° clockwise (b) 40° counterclockwise (c) Draw Mohr's circle on scale and show the stresses of parts (a) and (b). 200 MPa 100 MPa 150 MPa

Q.1) For the state of stress shown below, use stress transformation equations to determine the normal and shear stresses after the element has been rotated (a) 30° clockwise (b) 40° counterclockwise (c) Draw Mohr's circle on scale and show the stresses of parts (a) and (b). 200 MPa 100 MPa 150 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5) A material is subjected to two mutually perpendicular linear strains together with a shear strain. Given that this system produces principal strains of 1x 104 compressive and 3x 104 tensile and that one of the linear strains is 2.5x 104 tensile, determine the magnitudes of the other linear strain and the shear strain by using Mohr's strain circle. Also, find the values of the principal stresses present in the material by using Mohr's stress circle. For the material, take E=208GN/m² and v=0.3
The state of plane stress at a point is shown on an infinitesimal element below. Determine the stresses at the point on an element that is oriented 65° counter-clockwise from the x, y axes shown. Enter the shear stress on this rotated element Ta'y' (with correct magnitude and sign) in kPa correct to 3 significant digits below. 300 kPa y 400 kPa X 400 kPa 300 kPa
1. A material is subjected to equal bi-axial tensile stresses of 60 MPa along the x- and y-axes. There is no additional stress. Determine the shear stress on the (1 1 1) plane toward the [1 0 -1] direction.
Calculate the unit normal vectors to the planes on which the three principal stressesact.
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
(c) For the given state of stress determine the following: (1) Principal stresses and its orientation (2) Normal and shearing stress after the element shown has been has been (a) 25° clockwise and (b) 10° counterclockwise. sketch a properly oriented element 10 MPa 30 MPa 50 MPa
Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane shear stress and corresponding and normal stress. 100 MPa 150 MPa Tay - 50 MPa
The normal and tangential stresses on a plane inclined at 30° to the axis of the minor principal stress are 75 N/mm2 and 20 N/mm2. The resultant stress on a plane by analytical method is
6. A steel bar with an ultimate strength of 1110 MPa is carrying a 305.8104- metric ton load, F. It is attached to a support by a rectangular steel pin with a known cross-sectional dimension of 1 = 11 in. What is the unknown cross- sectional dimension, w (in inches), if the bearing stress is 9.68703 ksi and the shearing stress is 3.07869 ksi in the pin? What is the shear stress in the pin (in kPa) if the modulus of elasticity of steel is 200 GPa? F Rectangular Cross Section
Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension. (a) Draw the Mohr's circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stress acting on a plane that is 30° from the major principal plane. kindly answer the following with a complete solution so that i can understand how to solve it. thank you