Q.1 A structure is supported by braces each of which transfersP = 160 ka load P = 160 kips to the base of a column as shown infigure. A cap plate at the bottom of the brace distributesCap platethe load P to four flange plates through a pin to twogusset plates. Diameter of Pin and thickness of flange- Pin (d, = 2 in.)- Flange plate(t=1 in.)plate and gusset plate are provided in figure. Determine(a) The average shear stress in the pin.(b) The average bearing stress between the flange plates andGusset platethe pin.(4 = 1.5 in.)(c) The normal axial stress in gusset plate. Assume thatP/2P/2gusset plate is 4 inch wide.

Given data: P (load on column) =160 kipsPt (load on each column) =1604=40 kipstf (flanged…

Answered: Q.1 A structure is supported by braces…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

A В C 12 kN For the frame and loading shown, determine the components of the forces acting on member DABC at B and D. 0.5 m D E F 6 kN 0.5 m H 0.6 m 0.4 m 0.2 m
3. The roof truss is subjected to the loadings shown. Determine the force in each member and indicate if the members are in tension or compression. Approximate each joint as a pin. 200 N 300 N 300 N 1.5 m D. B. 4 m 3 т G 3 m 3 m E 3 т Paist X Ute 150 N
The armor shown supports a pedestrian bridge between two buildings that it exercises vertical forces of 50 kN in B, D, F and H. The supports in A and in I are supports of rollers.to. Use the section method to determine the axial force in the BC bar.Conclude if the elements are under tension or compression.
Asap plzz .... Vll give thumbs-up
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
1. Given the values of the load L and dimension R, for what value of the couple M will the force in link CH be equal to 10 kN, compressive? Note that R = 2m and L = 50 kN. FR R -R D C в м А F G E to -R- - 2R Given: (figure); R = 2m, L = 50kN Required: M so that FCh = 10 kN,C
Solve the following problem and show your complete solutions. Explain your answer for better understanding.
Rigid members ABC and DEF are joined bysteel (Es = 180 GPa) links BE and CF. The steellinks consist of rectangular plates with crosssectional dimensions 25x35-mm. Determine:a) the change in length of BE and CFb) the distance between pts. A and D after theloading is applied. Pts. A and D are 240mm apart prior to the applied loading.
Please Asap
Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa. c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4. Use appropriate (SI) units as it applies (if any.)
I need the answer as soon as possible
A force pair M is applied on a plane that makes an angle with the vertical to the beam of which cross-section is shown. Find the stress at D point.

SEE MORE QUESTIONS

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning