1. The figure below shows a Warren girder consisting of seven members each of 3 mlength freely supported at its end points. The girder is loaded at B and C as shown. Findthe following:a. The reactions at point A and D.b.compressive or tensile.The forces in all the members of the girder, indicating whether the force is2 kN4 kNBК60°60°60°60°E6 mShow your solution and then summarize your answers here:MemberNature of force(Tension or Compression)Magnitude of force in kNАВAEВСBEСЕEDCDņ (3 II

Answered: Image /qna-images/answer/cd1b68d5-d194-4dc6-a09b-84b41e4d9d83.jpg

1. The figure below shows a Warren girder consisting of seven members each of 3 m length freely supported at its end points. The girder is loaded at B and C as shown. Find the following: a. The reactions at point A and D. b. The forces in all the members of the girder, indicating whether the force is compressive or tensile. 2 kN 4 kN 60 60°60° 60° E 6 m Show your solution and then summarize your answers here: Member Magnitude of force in kN Nature of force (Tension or Compression) АВ AE ВС BE CE ED CD

1. The figure below shows a Warren girder consisting of seven members each of 3 m length freely supported at its end points. The girder is loaded at B and C as shown. Find the following: a. The reactions at point A and D. b. The forces in all the members of the girder, indicating whether the force is compressive or tensile. 2 kN 4 kN 60 60°60° 60° E 6 m Show your solution and then summarize your answers here: Member Magnitude of force in kN Nature of force (Tension or Compression) АВ AE ВС BE CE ED CD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 340 mm2 and a length of L1 = 3.6 m. Rod (2) has an area of A2 = 315 mm2 and a length of L2 = 1.2 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 60 kN is applied to the rigid bar at D, determine:(a) the normal stresses in rods (1) and (2)(b) the magnitude of the downward deflection of the rigid bar at D.
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 2L 1 4L 3L 60° Answers: Ay i Dv = i Dx= i = B 60° 60° E 2L L 30⁰ L ! L D
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
determine the support reactions at point A,B & C. TAKE NOTE: The support C is fixed and Support B is an internal hinge. Kindly show your complete solutions.refer to the given figure below.
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 2240 N, a = 3.3 m, b = 6.6 m, 0 = 47° Answers: AB= AC = B AD = Ꮎ Jak a Ө b Ꮎ N Z Z N N D F
Determine the force in all members of the truss shown in the figure below. State whether the members are in tension or compression. The reactions at the supports have been calculated. Ax=0- A B A₂ = 9 KN 6 KN M H |+ 3 m G 8 KN 3 m D F 2 KN 3 m ** 3 m E [SM. JASM 4.5 m 3 m E₁ = 7 KN
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN
b) A frame designed to test the compressive strength of concrete blocks is composed of the four pressure pads, the four compression links, and the three outer links arranged in a square as shown. Express the compressive force C acting on each side of the square concrete block in terms of the applied forces P. P P Activ Go to S
The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)