Q. A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficients of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.

Q. A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficients of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) In an engine governor of the Porter type, the upper and lower arms having equal length, 200 mm and pivoted on the axis of rotation. The mass of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 25 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30° and 40°, find, taking friction into account, range of speed of the governor.
Example: An automotive single-plate clutch with twe of friction Surfaces, transmits a 300 N-m to- pairs rque at 1500 rp.m. The inner and outer diameters of the friction disck are 170 and 270 mm The cofficient of friction is 0-35. The normal for- ce on the friction Surfaces is exerted by nine helical Compre ssion springs, so that the clutch is always engia- ged. The clutch is dis engaged when the external force Further Compresses (5) and the number of ac Five Coile are (6) The are made of patented and Cold-drawn steel respectively. the springs. The spring index is Springs wires of minimum tensile Stmength (MTS) (N/mm?)as Wive dia. 1 1-21-4 1.6 1-8 2 2.53 3.6445567 MTS, 1900 i2601817e0175017201640 1570 I510 1480 440 139013201260 NI mr The permissible shear stress for the wire is 30%. of the ultimate tensile strength, and (G-81370 Nimn). Design the springs and specily their dimensisns. Use this relatian to obtaine to the total normal fore required to transmit the torque. F= 4T where Dis…
Solve fast
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
Q2/ A conical clutch an included angle of 60°. the outer radius and inner diameters are 80 and 20 cm respectively. Calculate the maximum and minimum intensity of pressure and force required to press the two halves together if it is to transmit 20 MW, at 60 rev/h. the coefficient of friction is 0.3, Use both the uniform wear theory and the uniform pressure theory.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
A multidisk clutch is required to have a torque capacity of 300 N.m. Due to space limitations, the inner and outer diameters are specified to be 62 mm and 128 mm respectively. The coefficient of friction is 0.30 and the limiting pressure for the friction material is 900 Pa. Find the minimum number disks using uniform-wear model. Please be clear on your solution!
Q3-a/ What are the characteristics of material which used for lining friction surfaces of a clutch? (5Marks) b/ An engine developing 45 kW at 1000 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed (0.1 N/mm2). Determine: 1. The face width required, and 2. The axial spring force necessary to engage the clutch Answer question 4 or 5 (15 Marks) 15 Q4/ The areas of the turning moment diagram for one revolution of a multi-cylinder engine with reference to the mean turning moment, below and above the line, are - 32, + 408,-267, +333,-310, +226,- 374, + 260 and 244 mm². The scale for abscissa and ordinate are: 1 mm = 2.4° and 1 mm = 650 N-m respectively. The mean speed is 300 r.p.m. with a percentage speed fluctuation of± 1.5%. If the hoop stress in the material of the rim is not to exceed 5.6 MPa, determine the…
A clutch functions to continue the power of 110 Hp and 3600 rpm rotation, number of clutch plate 1, The total force of the spring suppressor 1500 N, correction factor 0.95 and friction coefficient 0.3 Calculate the Measures of Do and Di if the ratio of Do: Di = 3: 2