Q : The cAank and connecting rod of steam engine O:Sm and 2:5m aue long. The Counter clock-wire clank eevolves with 200 epm direction. when in 40° from find 1. Velocity of tuned innee dead it has centre position. 2. Angular veloeity of comnecting 1od?

Q: Q : The ciank and connecting rod of steam engine O:Sm and 2:5m aue long. The counter clock-wire…

A: Given data  crank length (r) = 0.5 m connecting rod length (l) = 2.5 m crank speed (N) = 200 rpm…

Q: State the rotational equation of motion.

A: Like translational motion, the displacement, velocity, and acceleration are also defined in…

Q: i need her solving with explanation how do I know the grashof condition and the barker clasification…

A: Sure, I can help you with solving the pin-jointed four-bar linkage problem and explain the Grashof…

Q: A 190 D TAB @AB,CAB 500 mm Figure 1 B AY = The crank AB rotates with an angular velocity of WAB 3…

A:

Q: For the following mechanism, Given: Lengths: O₂A=4 in, O3B=8 in, BC=5 in., O2O3-4 in. and offset…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: H.W.4 Drive the maximum acceleration for rear wh el drive on an inclined road ( aM).

A:

Q: pls explain and show to me  the DIAGRAM OF OPEN DIFFERENTIAL IN ROLLER BEARINGS thanks

A: An open differential in roller bearing consists of the following elements. a) Differential case: It…

Q: For the following mechanism, Given: • Lengths: O₂A-4 in, O3B=8 in, BC=5 in., O2O3-4 in. and offset…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Locate all the centros and determine the linear velocities of point C, D, E in ft/min and angular…

A:

Q: PLEASE NOTE: Solve GRAPHICALLY!! USE THE INSTANTANEOUS CENTER OF VELOCITY APPROACH A moving…

A: from triangle CBI, IC=0.6tan60=0.346IB=0.6/sin60=0.693vc=IC.ωBCωBC=vc/IC=3.6/0.346ωBC=10.39 rad/s…

Q: A motorcyle with 20 in wheel is travelling down a road at 15 mi/hr A. Find the angula velocity in…

A: Given data: d=20 in=0.508 mv=15 mi/hr=402.336 m/min Need to determine the angular velocity in…

Q: If rod CD is rotating with an angu lar velocity wcD= 16, determine the followings: Lengths: AR =40…

A:

Q: Problem 2. For the mechanism in the configuration shown in the Figure, ro28 = 4.0 cm, rDB = 10.0 cm,…

A:

Q: polar mass moment of inertia

A: Given; Maximum fluctuation of KE in an engine has been calculated to be,∆E=2600 JAssuming that the…

Q: 2. A disk that is 3 m in radius spins at the rate of 4 revolutions per second and over a period of…

A:

Q: B has constant C.W. angular veloc- rad/s, arm BC has constant an- city of 0.4 rad/s, and arm CD re-…

A:

Q: A bloek of plane 1osts inclined at o with the hori zontal, The block is attached to a spring' mass…

A:

Q: Lengths: O₂A-4 in, O3B=8 in., BC=5 in, O2O3-4 in. and offset c=10 in. Angles: 8-60° and -45° The…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: please answer and explain be specific and i will upvote if correct and explained

A: Step 1:

Q: A SCARA manipulator which has two revolute joints (0,A) and one prismatic joint (B) is shown in…

A:

Q: Skedch the motion of a damped oscillator for three Cases ) Underdamp ()cnitically damp and (ii)…

A: (i) For under-damped system, the expression for the motion can be written as below,…

Q: can you pls provide the wxcat solution for quation of motion with complete explaition by hand…

A:

Q: The dingram Shows mass On 4uo ro tors in planes. B and c. Calculate The masses to be added On the…

A: Given:- mB=5kg mC=3 kg Radius=40mm Radius of mB=20mm Radius of mC=50mm AB=80mm BC=70mm CD=100mm

Q: Given: (RCH 12th 16.96) The mechanism and kinematics shown below. 0.15 m 45 Ylos 0.45 m TE/B "c-3…

A: vc=3m/sAngle=45°

Q: 0.2 m B 30° A WAB= 10 rad/s At this instance, the link BC is rotating O clock wise O counter clock…

A:

Q: HHOW many minutes after 2 o' clock will the handc of the clock be pen diculer for the first time ?

A: Given 2'O clock To find Perpendicular arm

Q: What is inertial reference frame?

A: An inertial reference frame is also known as an "inertial frame of reference". Newton's first law of…

Q: in an 1.C. Engine Mechanism the peripheral velocity of crank pin is constant at 150 cm/s. and · it…

A: In this question, we know that the peripheral velocity of the crank pin in an I.C Engine Mechanism…

Q: ) geas useim steering as pe Spuy bevel © toerm Helical usd after motor to damping vtalari Spus gear…

A: 1)Gear used in steering air planes - (a) Spur gears   2) Used after motor for damping vibrations -…

Q: e direction shown. Positive angular velocity and acceleratior e in the counterclockwise…

A:

Q: entre. If the moment of

A:

Q: In 4 bar mechanism, suppose if the crank does not rotate with constant angular velocity, then the…

A: In a four-bar mechanism, the crank is the shortest link that rotates fully if it is attached to the…

Q: If rod CD is rotating with an angu lar velocity wcD= 16, determine the followings: Lengths: AN =40…

A:

Q: A disk is driven by a motor such that the angular position of the disk is defined by 0 =(141+1412)…

A: Here, angular position, θ=(14t+1.4t2) rad and angular velocity, ω=dθdt=(14+2.8t) rad/s

Q: 1) Find VA, VB, and wz when Link 2 = 2, Link 3 = 6, offset = -3, 02 = 60°, w2 8rad/= 2) Find VA, VB,…

A:

Q: A slider-crank mechanism is required whose slider is at position 12 cm when its crank is at  90°.…

A: Given data: Position of slider-crank mechanism from the crank center = 12 cm…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.