Q/ Read the program carefully, what is (A) at the end of program? Why? (Let the mean program saved in memory with starting address (3000H)) LXI SP, 4000 LXI D, 300D LXI H, 3301 CALL 5000 ADD D MOV B, E MVI C, 44 HLT Subroutine PUSH D PUSH H POP PSW RC POP PSW RET

Q/ Read the program carefully, what is (A) at the end of program? Why? (Let the mean program saved in memory with starting address (3000H)) LXI SP, 4000 LXI D, 300D LXI H, 3301 CALL 5000 ADD D MOV B, E MVI C, 44 HLT Subroutine PUSH D PUSH H POP PSW RC POP PSW RET

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Q: Assume that [SP]= 01FF. Then Consider the following program: PSH X PHSY PSHA PULA i) ii) Show the…

A: Contents of Stack:- after PSH X: X will be in the Stack after PSH Y: Y,X will be in stack after PSH…

Q: Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the…

Q: When input PB2 is actuated: L1 Inputs oto-PB1 toto PB2 PB1 C5:0/DN B3:0/0 CTU HEE OSA COUNT-UP…

A: According to the question, for the given PLC diagram as shown below We need to find the status of…

Q: snip

A: (a) There are nine tasks A1, A2, A3, B1, C1, C2, D1, D2, and E1, the precedence diagram is shown as

Q: Suppose that initially the contents of the registers are A:07 B:A9 SP:004F X:34BF and that memory…

A: As given in the question the registers are A:-07 B:-A9 SP:-004F X:-34BF

Q: Suppose that initially the contents of the registers are A:A7 B:69 SP:004E Y:B804and that memory…

A: Given data, Initially, the memory location 0048 – 004F are set to zero. Step-1 The most…

Q: Which of the sentences is WRONG concerning the following code? Ladder logic program Timer_Sw 36…

Q: Results of arithmetic and logic instructions can be stored in one of two places. These are Program…

Q: Which of these registers are not used to store the EA in the Register indirect addressing a. BX b.…

A: The correct option is SP(STACK POINTER).

Q: 20. In Figure 5, How many clock pulses are required to add two, 4 bit binary number ? Register B…

A: The given circuit diagram is

Q: 1 List the logic gates names that have been used in the given combinational logic circuit. 2. Write…

A: Introduction: There are different kinds of logic gates like AND, OR, NOT, EX-OR, EX-NOR, NAND, and…

Q: please solve on a paper, no chatgpt

A: In little-endian systems, the least significant byte is stored at the lowest memory address. So,…

Q: If d8 is 04H, BX contains 1234H, and DS contains 2000H, what docs the instruction of MOV AX, d8[BX]…

Q: Which one of the following instructions will cause a memory read when it is executed? MOV BL, AL…

A: MOV BL, AL This instruction will copy from register A to register B. Both source and destination are…

Question

Q/ Read the program carefully, what is (A) at the end of program? Why?
(Let the mean program saved in memory with starting address (3000H))
LXI SP, 4000
LXI D, 300D
LXI H, 3301
CALL 5000
ADD D
MOV B, E
MVI C, 44
HLT
Subroutine
PUSH D
PUSH H
POP PSW
RC
POP PSW
RET

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Tracing the program

VIEW

Step 3 Answer

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Different Types of System and Its Property

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is the content of SI after executing the MOV SI, [DI+BX+7H] instructions? * Memory Memory address content 12300 11 12301 AA 12302 EF 12303 80 12304 47 12305 8D 12306 5A 12307 92 12308 C5 SI = EF80H SI = 80EFH SI = 92C5H SI = C592H
I need the answer as soon as possible
To select the ROM the address lines A10-A9 should be: A. 00 B. 01 C. 10 D.10
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
I need the answer as soon as possible
Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 01100 For this circuit:Draw the logic circuit for the datapath.
Question in photo please ASAP Hand written also thanks
question1:In a memory system, data is 16-bit wide. Break the information into bytes with their addresses using little endian and big-endian methods. Starting address is F800 and the data is: E0F2 0041 question2:What acknowledgment signals are there in I2C bus?
New Solution
QO dddd Q1 clock Given: • Counter starts at decimal 9 when Q viewed as a 4-bit unsigned number (Q3 most significant bit) What is the decimal value of Q (viewed as a 4-bit unsigned number) after four more clock “ticks"? Answer
part d, e, f
Suppose that initially the contents of the registers are A:07 B:A9 SP:004F X:34BF and that memory locations 0048 through 004F initially contain all zeros. The commands PSHA, PSHB, PULA, PULB, PSHX are then executed in sequence. List the contents of the registers A, B, SP, and X, and the memory locations 0048 through 004F after each command is executed.