Which of the sentences is WRONG concerning the following code?Ladder logic programTimer_Sw36Status_Timer.EN36Status_Timer.TT36Status_Timer.DNHEO a.O b.O d.TON-TIMER ON DELAYTimerPresetAccume.None of the choices(EN)10000-(ON)5000-Status_TimerEN PL-(-TT_PLDN_PLO c. Once the Timer_Sw is ON for 10 seconds, the light DN_PL is ONWhenever the timer accumulator equals 10000, the done bit is turned ONThe light TT_PL will be ON whenever Timer_Sw is ONThe light EN_PL will be ON whenever Timer_Sw is ON

Answered: Image /qna-images/answer/471fbe1c-690b-41a5-8e0c-8a68ea8db8a3.jpg

Which of the sentences is WRONG concerning the following code? Ladder logic program Timer_Sw 36 Status_Timer.EN 36 Status_Timer.TT 36 Status_Timer.DN H O a. None of the choices O b. 0 c. TON TIMER ON DELAY Timer Preset Accum O d. Status_Timer 10000 (DN) 5000- EN_PL TT_PL DN_PL Whenever the timer accumulator equals 10000, the done bit is turned ON Once the Timer_Sw is ON for 10 seconds, the light DN_PL is ON The light TT_PL will be ON whenever Timer_Sw is ON

Which of the sentences is WRONG concerning the following code? Ladder logic program Timer_Sw 36 Status_Timer.EN 36 Status_Timer.TT 36 Status_Timer.DN H O a. None of the choices O b. 0 c. TON TIMER ON DELAY Timer Preset Accum O d. Status_Timer 10000 (DN) 5000- EN_PL TT_PL DN_PL Whenever the timer accumulator equals 10000, the done bit is turned ON Once the Timer_Sw is ON for 10 seconds, the light DN_PL is ON The light TT_PL will be ON whenever Timer_Sw is ON

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

give the final result of operation that appears onto OUT-Reg. after convert the whole program below into Op-code? Address OH 1H 3H 4H 5H Mnemonic LDA AH US Address 6H 7H 8H 9H AH BH CH DH EH FH DATA FFH FFH FFH 01H OEH 01H OFH FFH FFH FFH
16) Answer each of the following with reference to the overfill alarm program shown in the figure below. a. Assume that the vessel is filling and has reached the 300-lb point. State the status of each of the logic rungs (true or false) at this point. b. Assume that the vessel is filling and has reached the 480-lb point. State the value of the number stored in each of the following words at this point: (1) I:012 (2) N7:1 c. Assume that the vessel is filled to a weight of 502 lb. State the status of each of the logic rungs (true or false) for this condition. d. Assume that the vessel is filled to a weight of 510 lb. State the value of the number stored in each of the following words for this condition: (1) I:012 (2) N7:1 18 e. With the vessel filled to a weight of 510 lb, state the status of each of the logic rungs (true or false). Inputs Ladder logic program Ouputs Fil Stop Start Full solenoid L2 Fill Fil solenoid solenoid Fill Filing solenoid Filing Full Ful GEQ GREATER THAN OR EQUAL…
Can you write the answer with assembly code using 8051 architecture?
Logic and switching theory
What are the two primary categories of output circuits that are used in TTL?
Q1:-State if the following statements are true or falls. 1. In general the time constant of sensor is larger than the time constant of Process. 2. The control valve is used to convert the sensor signal to an equivalent signal. 3. In Routh stability you can find the number of unstable roots. 4. Dead time is also called pure delay.
Q 2
Using logic gates, draw a logic circuit for adding and subtracting numbers (numbers converted to formula 01) where the input is by switches and the output is connected to Segment ships to display the result of the addition and subtraction process, the circuit is 4 bits.
Q7) Give the State Machine for detecting the sequence “1010” from a serially coming data.
Please answer the question
Q3: Draw a ladder logic diagram to control the lamp output as per the given logic. Make use of On-Delay timers(TON) for this problem. START WITH PUSH BUTTON L1, L2 (2 sec) L3, L4 (4 sec) L5, L6 (6 sec) L1, L3, L5 L2, L4, L6 ALL ON ALL Off ON ON ON OFF OFF (8 sec) (10 sec) (12 sec) (12 sec)
QUESTION 1 You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX, 6543 1369:0103 BB3394 MOV BX, 9433 1369:0106 F7E3 DEC BX 1369:0108 CD21 INT 21 The last byte of the instruction loaded at address 0106 is stored in address. 0100 0106 0107 0108