Q: Liquid water at 20°C flows out of a nozzle straight up 20.387 m. and aera exit 0.25m2, take density of water is 1000 kg/ m3. The volume flow rate is * 5 points 50 m3/s 5 m3/s 0.5 m3/s Potential energy of water is * 5 points 1000 KW 10000 W 1000 W Specific Potential energy of water is * 5 points 200 J/kg 2000 KJ/ kg 200 kJ/ kg

Q: Liquid water at 20°C flows out of a nozzle straight up 20.387 m. and aera exit 0.25m2, take density of water is 1000 kg/ m3. The volume flow rate is * 5 points 50 m3/s 5 m3/s 0.5 m3/s Potential energy of water is * 5 points 1000 KW 10000 W 1000 W Specific Potential energy of water is * 5 points 200 J/kg 2000 KJ/ kg 200 kJ/ kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermodynamics
show all working out please
Find the air horsepower of an industrial fan that delivers 26 cu.m/s of air through a 1 m x 1.2 m duct3; pressure of 127 mm of water; air temperature is 21 C and barometric pressure is 760 mm HG. 43.18 kW 42.62 kW 38.12 kW 39.72 kW
The water is flowing through a pipe having diameters 40 cm and 17 cm at sections 1 and 2 respectreely, The rate of flow through pipe is 45 liters / s .The section 1 is 7 m above datum and section 2 is 4.5 m above datum it the pressure at section 1 is 38.5 N /cm2. find the following by neglecting losses find: 1) Area of cross section of section 1 (UNIT in m2) 2) Area of cross section of section 2 (UNIT in m2) 3) Velocity head at section 1 (UNIT in m ) 4) difference in datum head (UNIT in m) 5) pressure at section 1 ( UNIT in N/m2) 6) pressure at section 2 ( UNIT in N/m2)
The compressed air network of a foundry with a volume V = 30 m³ is filled by a compressor in 47 = 30 min. Therefore the state of the air changes from pi = 0.15 MPa, t₁ = 25 °C to p2 = 1.0 MPa at constant temperature. a) Which mass of air Am is fed into the compressed air network? b) Which air volume flow Vo in the intake state of the compressor (po = 1000 hPa, to = 10 °C) is required for filling? The air mass flow required for a pneumatic hammer is subsequently provided in state 3 from the compressed air network. The pressure is throttled adiabatically to p3= 0.5 MPa, the air volume flow is V3 = 1.4 m³/min. c) What is the air mass flow m required by the hammer? d) What power P34 does the adabatic pneumatic hammer deliver, if a temperature t4 15 °C is measured at the air outlet?
An oil refinery uses a Venturi tube to measure the flow rate of gasoline. The density of the gasoline isp = 7.10 x 102 kg/m³, the inlet and outlet tubes, respectively, have a radius of 2.36 cm and 1.18 cm, and the difference in input and output pressure is P, - P, = 1.20 kPa. P1 P2 (a) Find the speed (in m/s) of the gasoline as it leaves the hose. m/s (b) Find the fluid flow rate in cubic meters per second. m/s
Q1. Two pumps with 105.4 cm in diameters characteristics shown in figure below are used in paralel to pump water to the system. Neglecting local losses, calculate total flow rate and pump power. (a) n= 710 d/dak 120 7.5 80m ENPY (2) 6. 105 - 105.4 cm çap S N 4.5 3 90 96.52 cm çap 88% 86% 75 - 88.9 cm çap S4% (1) bom 60 1100 kW 45 750 kW 30 0.25 0.50 0.75 1.00 1.25 1.50 1.75 Debi m/s Note: Pipe is cast iron with 0.6 m in diamater and 1.6 km in length. Fluid is water with density 1000 kg/m³ . ENPY m %68 900 kW
Containers A and B containing real fluid are combined like. While the difference of water levels of the reservoirs is h = ab (m); i-) Find the flow rate of the water passing from chamber A to chamber B. ii-) Draw the Energy and Piezometer lines of the system. g = 9.81 m / s
I need the answer as soon as possible
The volume of air delivered by fan is 14 m^3/sec and 69 mm water gage. The density of air is 1.27 kg/m^3 and the motor power needed to drive the fan is 51 kW. Determine the fan efficiency in % Answer in whole number
A circular pipe CD carries 1/3rd of flow in AB. Find volume rate of flow in AB, diameter of BC, velocity in CD and diameter of CE. B, 4Q o8 m 4m/s +2.2 m 1.8m/s 2.25m/s
Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 ft 4 in, diam Water