In Fig. 3 below, the pump move water from tank A to pressurized Tank B at rate of 100 m³ in 5 min. Perform appropriate calculation to determine if the pump with 2.5 hp works for this purpose. Repeat the calculation and determine if the pump works with air pressure in Tank B of 2.5 atm instead 1.5 atm. B P-15 atm tow ee 4m 50 m 4m Pump

In Fig. 3 below, the pump move water from tank A to pressurized Tank B at rate of 100 m³ in 5 min. Perform appropriate calculation to determine if the pump with 2.5 hp works for this purpose. Repeat the calculation and determine if the pump works with air pressure in Tank B of 2.5 atm instead 1.5 atm. B P-15 atm tow ee 4m 50 m 4m Pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system curve for a water supply system is shown in the figure below (i.e., red curve). If a 7-inch pump is operating at 1160 rpm, what will be the discharge of water through the system in GPM? Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 HEAD IN FEET 30 25 W 20 10 5 L/SEC 5 7.00" (178mm) 6.75" (171mm) 6.50" (165mm) 15 6.25" (159mm) 7.25" (184mm) O 150 GPM Laco O 350 GPM O 450 GPM O 250 GPM 10 Model 4075 FI & CI Series 15 70% 20 "Dede de 088 A. 25 REQUIRED NPSH 90 1160 RPM November 1, 2010 TM 90- N 00 30 8800 877 1HP(.75KW) de (5 60% ox 35 -10% 5% Tolo 10. 3HP(2.2KW) 2HP(1 5KW). 15HP(1 1KW). CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE 45 LOWONG FEET 15 12 9 6 0 6 5 + 2 1 750 NPSH HEAD IN METERS 45 36 OG KPO 27 18 -9 -70 -60 -50 -40 20 10 -0 HEAD IN KILOPASCALS
A pump has a volume displacement of 80 cm³. It delivers 75 LPM at 16 rotation per second and 70 bar. If the prime mover input torque is 100 Nm. a) What is the overall efficiency of the pump? b) What is the theoretical torque required to operate the pump?
pls use setting= 1
Provide the neccesary equations in designing a centrifugal compressor such as the dimensions for impeller. What are the initial given values?
1. If the pump rotated at 2000 rpm and instead and used a 9" impeller, what would the head be when moving 400 gallons per minute? 2. How much input power would be required to move 200 gpm of gasoline in the pump described in the chart with an impeller diameter of 8 3/4"?
B9
State the Heads of Pumps *
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
Water flows in a pipe and nozzle arrangement, having 0.1 diameter pipe and 0.05 m diameter nozzle that discharges to the atmosphere. Exit velocity at the nozzle is 84 m/s. a) Calculate the pressure at point 1. b) Pressure when the device is inverted.
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
Need proper solution, it should not be copied
A multi-stage centrifugal pump is to deliver 500 gpm of water at a total head 250 ft. Specific speed is 300 rpm and rotative rpm is 500 rpm. a) Determine the number of stages required b) If a single stage pump is used, what would be the rotative rpm, Ns = 300 rpm.