Q: compute the total elongation caused by an axial load of 100KN applied to a circular bar, tapering from a diameter of 120mm to 40mm in length of 10m assume E=200GPA. 100KN 100KN у 20mm 60mm dx 10m

Q: A bronze c86100 cylinder with diameter d₂ = 60 mm is nested inside a stainless steel tube with inner…

A: We must take into account the stress in both the stainless steel tube and the bronze cylinder in…

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Mpa steel bronze A= 300mm2…

A: Given: The maximum allowable stress in steel rod = 120 MPa The maximum allowable stress in bronze…

Q: What is the total elongation of steel bar having a diameter of 2 in. hanging over with a length of…

A:

Q: Two columns have the following parameters: Column A Column B Length Cross sectional area 1.5m 2m…

A: It is the very basic but comparative question of theory of columns portion of strength of material.…

Q: A 'L' shaped post with a cylindrical cross-section is loaded with a concentrated load at its free…

A: Given: To find: State of stress at P1

Q: Q2\ Find the necessary change in temperature in the copper bar so that the rigid bar remains…

A: For the rigid bar to remain horizontal, the moment due to the UDL should be equal to the moment due…

Q: Q3/ Thickness of plate is 5mm and its yield stress is 630 MPa with endurance limit equals 225 MPa,…

A:

Q: Evaluate the maximum normal stress and strain, and its location at the beam where bending failure…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronzel A=…

A: σsteel=120Mpaσbronze=70Mpato find:- Maximum load(P)

Q: axial load (in kN) is

A: Given: For a simply supported steel column at both ends: length=1.5 mcross-section area=15 mm×10…

Q: Neglect the concentrated moment M and the concentrated load P and determine the deflection at B due…

A:

Q: 2) Reqd: Determine e of A relative to D G = 12 x 10° psi MN Ib t U-41 0001 1000 lb ft 900 lb ft er…

A:

Q: Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a…

A: Given data: - Thickness of the plate, t=35 mm,Width of the plate, w=160 mm,Length of the plate,…

Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…

A:

Q: a steel column that has a diameter of 50mm and 32m long is surrounded by an iron shell that is 5mm…

A:

Q: A short column is composed of two steel E-31.000 k v 0.30) segments, each with a length of 4.5 in…

A: Find , Deflection in the steel column.

Q: Select a standard rolled steel I-section for the simply supported beam of length 8 m and carries a…

A:

Q: Q: compute the total elongation caused by an axial load of 100KN applied to a circular bar, tapering…

A: Given:P=100 KNL=10 mD1=40 mmD2=120 mmE=200 GPa

Q: The one end of a hollow square bar whose side is 0.1 with  0.01 thickness is under a tensile stress…

A:

Q: Wire radius, r =15 mm R=90 mm G=8Y Gpa A=? J=? F= 1.X kN T=? Tr =? Ta =? Tr =? T =? Na=15 turns…

A: Helical spring Helical springs are the thick spring wires coiled into a helix. Helical springs are…

Q: = A bronze c86100 cylinder with diameter d₂ = 50 mm is nested inside a stainless steel tube with…

A:

Q: Ax 60° 384 100 luo 100kN Upt God

A:

Q: SITUATION A: A tension member consisting of two channels and two plates PL 13mm x 280mm arranged as…

A: Given data  PL 13mm x 280mm  Pdead load = 900KN and Pwe lba = 1400KN. The member is assumed to be 9…

Q: Two squared and ground end springs arranged in series. Find the total deflection in mm. The springs…

A:

Q: Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 KN tensile load if the…

A:

Q: Torsion Load 100 mm- Shafts ABC and DEF are made of A36steel. Shaft ABC is connected to an…

A: Given: The motor power, P = 2 kW The speed of shaft ABC, N = 62 rpm The factor of safety of shaft…

Q: A short column is composed of two steel (E-31.000 k v=0.30) segments, each with a length of 4.5 in…

A: The shortening of the segments: ( 3.76408 × 10-4 ) inch.

Q: A horizontal beam AC is supported by a square bar BD. Assume that the pin placed at B is adequate to…

A:

Q: Question 5 required to raise the load if the yield stress of steel is 300MPA. A lead of 5kN is to be…

A:

Q: with a stress of 52.89  and diameter of 4cm and thickness of 2mm  (P) load of 2MPa how was the…

A:

Q: Determine the equivalent stiffness constant of the f

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.