Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of 60 тm. 200 mm 60 mm P P 0 mm 160 m | 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 M Pa and the shear strength of the pin is 100 MPa.

Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of 60 тm. 200 mm 60 mm P P 0 mm 160 m | 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 M Pa and the shear strength of the pin is 100 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25…

A: Given data, Width of the main plate, bm = 300 mm Thickness of the main plate, tm = 20 mm Thickness…

Q: A bronze c86100 cylinder with diameter d₂ = 60 mm is nested inside a stainless steel tube with inner…

A: We must take into account the stress in both the stainless steel tube and the bronze cylinder in…

Q: The pulleys in the system are under the influence of the forces shown in the figure. The yield…

Q: Q3/ Thickness of plate is 5mm and its yield stress is 630 MPa with endurance limit equals 225 MPa,…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

Q: A) What is the axial force along AB? FAR = units B) What must be the minimum diameter of the pin at…

A: Given:P=200 lbFoS=2.5shear stress at failure for the pin material= 16 ksi

Q: For the structure shown below, the shear stress in the pin at B is determined a MPa if it has a…

Q: THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a…

Q: Situation 4: A rigid plate of negligible weight rests on the central spring as shown and is loaded…

A: Given: The load acting on central springs, P = 5+2x5+4 = 19 kN The gap between outer springs and…

Q: The one end of a hollow square bar whose side is (10+N/100) in with (1+N/100) in thickness is under…

Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…

Q: A short column is composed of two steel E-31.000 k v 0.30) segments, each with a length of 4.5 in…

A: Find , Deflection in the steel column.

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: Question 2) In the system given in the figure, a distributed load of w = 88 kN /m affects the AB rcd…

A: Given: load w= 88 kN/m; AB=4.1m; θ=56°; a=28mm;σm=212 MPa; ζm=70 MPa To Find: b? pin diameter at B

Q: Circular steel bars will be used in the cage system in the figure. Accordingly, find the safety and…

A: The roller at D gives the vertical reaction and the hinge at G gives the horizontal and vertical…

Q: The one end of a hollow square bar whose side is 10 in with 2 in thickness is under a tensile stress…

A: Given Data: The side of the hollow square bar is s = 10 in. The thickness of the hollow square bar…

Q: Q: compute the total elongation caused by an axial load of 100KN applied to a circular bar, tapering…

A: Given:P=100 KNL=10 mD1=40 mmD2=120 mmE=200 GPa

Q: 1 kN load is applied to the plates in shear, what is

Q: The one end of a hollow square bar whose side is (10.13) in with (1.13) in thickness is under a…

Q: A machine component made of a ductile material is subjected to a variable loading with Omin=-50 MPa…

A: Given:minimum stress=-50 MPamaximum stress=50 MPa

Q: a) The maximum normal stress occurring in the plate, b) Find the shear stress on the M10 bolt and…

Q: See the set of bars for made of a material that has a yield strength of 350 MPa, determine the…

Q: Cantilever steel rod is loaded by axial concentrated forces. F1 F2 F3 d 4 Given: 4-2,31; 12-2,91;…

A: Cantilever rod is one in which one of the ends is free from support and one end is fixed. The total…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Q: = A bronze c86100 cylinder with diameter d₂ = 50 mm is nested inside a stainless steel tube with…

Q: SITUATION A: A tension member consisting of two channels and two plates PL 13mm x 280mm arranged as…

A: Given data PL 13mm x 280mm Pdead load = 900KN and Pwe lba = 1400KN. The member is assumed to be 9…

Q: A 20KN load is applied at point A of lever ABC as shown in Figure Q2. Member ABC has a uniform…

A: A pin support will experience both horizontal and the vertical components of reactions. In…

Q: 8 mm x 36 mm Calculate the shear

A: for solution refer below images.

Q: The one end of a hollow square tube whose side is (10+N/100) in with (1+N/100) in thickness is under…

A: Data given - Side a = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in tensile stress σt =…

Q: A thrust collar that rests on a 0.95 in. thick polymer plate supports the vertical nylon shaft. The…

Q: Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 KN tensile load if the…

Q: 1) The section of the pipe at A is under combined loading due to a tensile force P=70 kips and a…

A: Given data:- Tensile force P=70 kips a torque T=6 kip-ft. Outside diameter = 4.0 in. Inside…

Q: For the lap joint below, the maximum safe load P if the bearing stress of the plate is limited to…

Q: A horizontal beam AC is supported by a square bar BD. Assume that the pin placed at B is adequate to…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of
60 тm.
200 mm
60 mm
P.
160 тm
35 тm
35 mm
200 mm
1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 MPa and the
shear strength of the pin is 100 MPa.
kN
Suppose that P is 140 kN, the Modulus of Elasticity is 200 GPa, and the Poisson's ratio is 0.3.
2) Determine the change in length of each plate.
тm
3) Determine the change in width of each plate.
тт
4) Determine the change in thickness of each plate.
mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 0.39 in. (Figure 1) Figure 1 in.- 400 lb 800 lb -1.5 in. 1 in. 400 lb Id W₂ a Part A Determine the maximum bending stress on the cross section at the center section a-a. Hint: For the solution it is first necessary to determine the load intensities w₁ and 2. Express your answer in kilopounds per square inch to three significant figures. max = Submit Provide Feedback -- ΑΣΦΑΤΗ1 VO Request Answer vec H ? ksi Next >
What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe figure if the ultimate shear stress in the 5-mmdiameter pin is 340 MPa?What is the maximum permissible value of theapplied load P to maintain a factor of safety of 3.0with respect to failure of the pin?
A machine member part is subjected to fluctuating stress of σ = ax cos(8nt) The endurance limit of the material is 350 MPa. If the FoS used in the design is 3.5 Find the maximum value of ?
Machine Elements The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Jall = 243 ksi for pin material.
Consider the rod shown in (Figure 1). The rod is made of a material having an allowable normal stress of σallow = 100 MPa and an allowable shear stress of τallow = 50 MPa. Determine the minimum diameter dd of the rod to safely support the load. d=?
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
3. If P= 100KN, Compute the total deformation. 112 in 201 60 CM 90 cm 9p 4P 7P $=2ch $=6m 644ch E= 120 GPa E = 200 GPa = 100 GPO
(2) h Q11 what the value of P Which are safer on the rivets as shown in figure below. given that : T=100.34 MPa, ob=370.3 MPa, 19mm diameter of .rivets 12.5m 19mm 12.5m 250mm P.
The figure below shows a set of plates joined by a rivet, subjected to a force F of 22.5 kN. Considering that the rivet to be used must be able to withstand a shear stress of 100 MPa, and adopting a safety factor equal to 2, what is the smallest possible diameter of the rivet?
The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Oall 243 ksi for pin material.
Quickly please.
5